TECHNICAL DATA
Please read these assembly instructions carefully!
STAND
- Total height: 1190 mm
- Height support: 1020 mm
- Round base: ø 275 x 41 mm
- Base tube: ø 20 x 1000 mm
MATERIAL
- Round base: steel, galvanized, PA, TPE
- Base tube: steel
SURFACE pure white, powder-coated
WEIGHT 2.9 kg
XL-BOTTLE HOLDER (Euro bottle up to 2000 ml)
- Bottle size: width x depth: max. 120 x 102 mm
- Clamping range: depth 65 - 102 mm
- drip cup: ø 70 x 47 mm
MATERIAL
- Bottle holder: steel, polyamide
- Thread: steel, brass, zinc
SURFACE pure white, powder-coated
WEIGHT 0.75 kg
SAFETY INSTRUCTIONS
The safety of the stand depends on the:
ROUND BASE
Handle with care due to the load, do not drop
(crushing hazard).
MOUNTING
Ensure that all screw connection are tight.
SURFACE
Only use the stand on suitable, i.e. level and
stable floors.
LOAD
Only for disinfectant bottles with suitable size;
see above TECHNICAL DATA.
SURROUNDINGS
Negative external influences (knocks, dragging around,
vibrations, wind etc.) must be avoided.
HANDLING
When changing the direction of the dispenser bottle
always turn the entire stand. Never loosen the thread
3
of the bottle holder.
INSTALLATION INSTRUCTIONS
STAND
1
Place the round base (with rubber insert) on the floor,
2
screw the base pipe with the external thread into
2
the base plate as far as it will go.
XL-BOTTLE HOLDER
A. STAND MOUNTING
3
Screw in the threaded bolt of the bottle holder into
3
the base tube as far as it will go.
B. WALL MOUNTING
4
see fig.
4.1
-
4.5
(Screws not included in delivery)
C. PREPARING XL-BOTTLE HOLDER
5
Open the accessories bag:
5
a. wing nut M5 (2x), b. washer ø 5,3 mm (2x)
5
c. carriage bolt M5 x 12 mm (2x), d. clamping bracket
6
Fitting the clamping bracket
5.d
to the bottle holder:
6
- Slide the bracket from outside over the mounting bracket,
6
- insert the carriage bolts
5.c
from the inside,
6
- thrust washers
5.b
over the threads,
6
- screw on wing nuts
5.a
.
7
The drip cup can be removed for cleaning purposes.
7
Subsequently press the drip cup from above back
7
into the holder.
D. DISINFECTANT BOTTLE (not included in delivery)
1
8
Place the disinfectant bottle in the bottle holder,
1
9
clamp the bottle by means of the bracket
5.d
,
10
tighten both wing nuts
5.a
.
INFORMATION
NOTE: Stand and bottle holder are not
NOTE:
medically certified product.
- Negative effects of the disinfectant on the products
-
(surfaces, material) are not known to us.
- Nevertheless, we recommend to always remove possible
-
residues of the disinfectant in order to avoid possible
-
damage and to enjoy the product as long as possible.
- For cleaning purposes use a slightly damp cloth and
-
a non-abrasive cleaning agent.
Disinfectant is not included in the scope of delivery.
B.
WALL
MOUNTING
Total height
Support
height in
assembled
condition
4.1
Align holder vertically
4.2
Mark the drill holes
MOUNT
EXAMPLES
4.4
WOODEN BEAM
- Wood screw 4,5 x 35 mm
drill, countersink, blow out,
attach bracket, screw in
wood screws
4.5
PERFORATED BRICKS,
CONCRETE
- Plastic anchor 6 x 30 mm
-
with wood screw 4,5 x 35 mm
drill, countersink, blow out,
set the anchor,
attach bracket, screw in
wood screws
4.3
Pre-drilling
4.3
e.g.: ø 6 mm
4.3
Expansion anchor
4.3
ø 3 mm Wood
4.3
screw
D.
DISINFEC-
TANT BOTTLE
C.
PREPARING
XL-BOTTLE HOLDER
XL-
BOTTLE
HOLDER
STAND
A.
STAND
MOUNTING
80315 Disinfectant stand
80310
with bracket XL
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
80315-000-76 Rev.11 03-79-921-00 5/20
