K&K Sound Pure Mini Page 3 Installation Manual Download | Manualshive

Page: 3 / 24

background image

3

DISCLAIMER

Following the pickup installation instructions is
mandatory. Installation or removal of this product is at
your own risk. In no event will K&K Sound Systems Inc.
be liable to you or whomever you select for doing this
installation or removal in your place, for any damages
arising from your use of, or, the inability to use these
products. This includes any possible health hazards,
accidents, injury, any lost profits, or other incidental or
consequential damages, even if K&K Sound Systems
Inc. has been advised of the possibility of such damages,
or for any claim by another party.

TABLE OF CONTENTS

1.  Package contents .................................................... 4
2.  Tools & supplies needed ........................................ 4
3.  Superglue vs. “peel-and-stick” installation ........... 5
4.  Preparation .............................................................. 6
5.  Installation

5.1 Jig installation for pin bridges .................. 8

5.2 Installation for pinless bridges ................ 14

6.  Important superglue info ...................................... 17
7.  Installing the endpin jack ...................................... 18
8.  Removing superglued pickups .............................. 19
9.  Troubleshooting .................................................... 20

«
1
2
3
4
5
...
»

Summary of Contents for Pure Mini

























Reviews:

No comments

Related manuals for Pure Mini

Brand: AccuMASTER Pages: 2

Brand: Vega Pages: 76

Brand: Kane Pages: 19

Brand: Fancom Pages: 49

Brand: Taber Pages: 53

Brand: Saimo Pages: 101

Brand: Obelink Pages: 2

Brand: Leuze Pages: 9

Portable Grand DGX-670

Brand: Yamaha Pages: 93

Portatone PSR-410

Brand: Yamaha Pages: 65

HF scientific AccUView LED

Brand: Watts Pages: 40

Brand: ColorLite Pages: 68

Brand: Facom Pages: 48

Brand: VTech Baby Pages: 22

Brand: Kettler Pages: 4

Brand: Biral Pages: 15

Brand: Saxby Pages: 2

Brand: JUGS Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands