manualshive.com logo in svg

KANDA KEYFOB, Quick Start Manual, Page: 18 / 18

Share
Download
KANDA KEYFOB Quick Start Manual Download Page 18

that it will work with all FTDI drivers. You may need to roll back the 

FTDI driver first before update can be done. 
 

 
 

 
Using old software 

To continue to use older versions of Kanda software, you will need 
to roll back the FTDI driver. See 

www.kanda.com/files/RollBackDriverGuide.pdf

 for full instructions. 

 
Once Dongle2 has been updated, it will still work with previous 

versions of Kanda software. All starter kits supplied after June 2021 
will contain Dongle3.  

 

Dongle3 

Supplied from July 10

th

 2021. Dongle3 will work with all FTDI 

drivers and will also work with Kanda software versions below 
v8.0.0.

 

 

 

 

FURTHER INFORMATION 

 
Please contact 

[email protected]

 for technical support or go to our website  

support pages for latest software. 
 

See 

www.kanda.com/support

 

 

Contact details 

 

Website

: 

www.kanda.com

      

 

email:

 

[email protected]

        

 
Phone/Fax: +44 (0)1974 261 273 

 

 

 

 
 

Atmel, AVR and  associated logos  are  registered 

trade

 marks of Atmel Corp.  San Jose, CA, USA

 

 

Summary of Contents for KEYFOB



















Reviews:

No comments