background image

27

Katherm QK nano – 

Ultra-small trench heater with EC tangential fan 

 

 

4.42

Ready-to-install convector-based floor trenches

 Assembly and installation instructions

LCD display symbols

1

Display of setpoint room temperature

2

Current time

3

Timer program enabled

4

Weekday 

5

Alarm 

6

Selected function is locked

7

Eco mode 

8

Setpoint setting enabled

9

Fan control setting Auto-0-1-2-3-4-5

10

Ventilation mode

11

Cooling mode

12

Heating mode

13

Automatic Heating/Cooling changeover mode

Operation of the basic functions

Function

Description

Switch On/Off

Switch on by pressing key 2 or the navigator dial. When switched on, the display shows a temperature. Switch off 
by pressing button 2 or the navigator dial. OFF is shown.

Change temperature

Turn the navigator dial to the left to lower, and to the right to raise, the required temperature. Confirm the entry 
by pressing the navigator dial.

Fan speed

Change by pressing the side fan button or using the navigator dial. Briefly press the navigator dial once. Turn the 
navigator dial to the left to lower, and to the right to increase the required fan speed. Press the navigator dial 
once more to confirm the display. 
In Automatic mode, the speed is adjusted when the room temperature deviates from the setpoint temperature.

Heating/Cooling/
Recirculation

Change by pressing the side fan button or using the navigator dial. 
To change using the navigator dial, first press the navigator dial for approx. 1 second to move to the Fan stage 
selection. Then press the navigator dial once again for 3 seconds to go to the Time setting. Press again for approx. 
3 seconds to move to the Timer menu. Press again for approx. 3 seconds to move to the Mode menu. Press briefly 
to confirm the entry.

Timer program

The KaControl provides the option of setting a weekly timer. Refer to the separate KaControl instructions for this.

9

10

11

12

13

1

2
3
4
5

6

7

8

Summary of Contents for Katherm QK nano

































Reviews: