OPERATING INSTRUCTIONS
OPERATING YOUR KAMBROOK
HOT CUP
BEFORE FIRST USE
Remove any packaging material and promotional
labels before using your kettle for the first time.
IT IS RECOMMENDED WITH DuE CARE AND ATTENTION PLACED
ON THE FOLLOWINg PRECAuTIONS bEFORE OPERATINg THE HOT
CuP.
WARNINg: THIS KETTLE DISPENSES 250ML OF HOT WATER
CONTINuOuSLy PER OPERATION.
IT IS NOT POSSIbLE TO INTERRuPT AND STOP THE HOT WATER
FLOWINg OuT FROM THE DISPENSINg SPOuT ONCE ONE CuP OF
WATER (250ML) HAS bOILED. THEREFORE, yOu MuST ENSuRE
THAT A VESSEL/CuP IS CAPAbLE OF HOLDINg A MINIMuM
OF 280ML CAPACITy AND IS PLACED uNDER THE DISPENSINg
SPOuT OF THE KETTLE ON THE DRIP TRAy. DO NOT OVERFILL THE
CuP AS THE WATER IS VERy HOT.
THE APPLIANCE SHOuLD ALWAyS bE PLACED ON A FIRM LEVEL
SuRFACE WHERE NORMAL ACCESS FROM PERSONS (INCLuDINg
CHILDREN) WITH REDuCED PHySICAL, SENSORy OR MENTAL
CAPAbILITIES IS RESTRICTED.
IT IS RECOMMENDED THAT A VESSEL/CuP CAPAbLE OF
ACCOMMODATINg A MINIMuM OF 280ML OF VERy HOT WATER
IS PLACED uNDER THE DISPENSINg SPOuT AT ALL TIMES
TO CAPTuRE THE DISPENSED WATER SHOuLD THE uNIT bE
INADVERTENTLy TuRNED ON.
It is recommended that before the first use to fill
the kettle to the maximum level with cold tap
water, carry out several boil cycles discarding the
water each time from a vessel/cup capable of
holding a minimum of 280ml capacity. Then, discard
the water inside the water chamber as following.
EMPTYING YOUR RAPID BOIL
After the Hot Cup has completely cooled down,
unplug it from the mains supply socket.
Press the lid release button.
Hold your kettle sideways over a sink.
Then, tip the Hot Cup upside down.
Still holding the Hot Cup over the sink, turn it
the right side up and allow any water to drain
out of the spout.
1.
2.
3.
4.
5.
Repeat steps 3, 4 and 5 until the water has
been emptied from the Hot Cup.
Your kettle will only operate when positioned on
the power base with the ON/OFF switch in the ON
position. The kettle will automatically switch off
once the water has boiled.
Note: The maximum capacity of the Kettle is 1.5L.
OPERATION OF YOUR KETTLE
To fill the kettle with water, remove it from the
power base and open the lid by pressing the lid
release button. The lid will automatically open.
Fill with the desired amount of water. Do not
operate the kettle without water. Always fill the
kettle between the minimum and the maximum
marks on the water window. Too little water will
result in the kettle switching off.
Ensure that the lid is closed and locked firmly into
place before placing the kettle on the power base.
Place the kettle firmly onto the power base. Plug
the power cord into 230/240V power outlet and
switch ‘ON’.
Press the ON/OFF switch to the ‘ON’ position.
The power ‘ON’ light will illuminate.
Note: In choosing the size of vessel/cup, it is
recommend the capacity is not less than 280ml,
make sure the vessel/cup is positioned in place
before using. Do not overfill the cup.
The kettle will switch off automatically once
one cup of water (250ml) has boiled.
The hot water will flow out from the spout
under 60 seconds. Before removing cup, make
sure the water flow has ceased.
Note: The water flowing out from spout is hot and
contact with the hot water may result in scalding.
Therefore, this appliance should not be used
by children.
If you want to boil water again, simply press the
power ON/OFF switch to ‘ON’ position again.
If further heating of the kettle is not required,
switch off at the power outlet, unplug the power
cord and empty the water from the kettle. Replace
the kettle onto the power base and close the lid.
6.
1.
2.
3.
4.
5.
6.
KQK600_HOTCUP_IB_FA.indd 5
19/6/09 4:00:18 PM
