background image

Fully unwind the power cord before use.
Do not let the power cord hang over the edge of 

a bench or table, touch hot surfaces or become 

knotted. 
To protect against electric shock do not immerse 

the  power  cord,  power  plug  or  motor  base  in 

water or any other liquid.
This appliance is not intended for use by persons 

(including children) with reduced physical, sensory 

or  mental  capabilities,  or  lack  of  experience 

and  knowledge,  unless  they  have  been  given 

supervision  or  instruction  concerning  use  of 

the  appliance  by  a  person  responsible  for  their 

safety.
Children should be supervised to ensure that they 

do not play with the appliance.
It  is  recommended  to  regularly  inspect  the 

appliance.  Do  not  use  the  appliance  if  power 

cord, power plug or appliance becomes damaged 

in  any  way.  Return  the  entire  appliance  to  the 

nearest authorised Kambrook Service Centre for 

examination and/or repair.


Any maintenance other than cleaning should be 

performed  at  an  authorised  Kambrook  Service 

Centre.
This appliance is for household use only. Do not 

use  this  appliance  for  anything  other  than  its 

intended  use.  Do  not  use  in  moving  vehicles  or 

boats.  Do  not  use  outdoors.  Misuse  may  cause 

injury.
The installation of a residual current device (safety 

switch  is  recommended  to  provide  additional 

safety protection when using electrical appliances. 

It is advisable that a safety switch with a rated 

residual  operating  current  not  exceeding  30mA 

be installed in the electrical circuit supplying the 

appliance.  See  your  electrician  for  professional 

advice.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

and the processing blade or disc, have completely 

stopped before disassembling. Ensure the Speed 

Selector Dial is turned to the ‘OFF’ position, the 

appliance is switched off at the power outlet and 

unplugged, before removing the lid from the bowl. 

The  processing  bowl  should  then  be  unlocked 

from the motor body and the processing blade or 

disc holder carefully removed before attempting 

to remove the processed food.
Do not blend a dry, thick or heavy mixture for more 

than 60 seconds without turning the blender/food 

processor off and stirring the ingredients before 

continuing to blend.
If the food processor is operated continuously for 

too long, it should be allowed to rest for 25-30 

minutes before recommencing.
Do  not  use  the  processor  and  blender  at  the  

same time.

Do  not  process  hot  or  boiling  liquids  –  allow 

liquids to cool before placing into the processing 

bowl or the blender jug.
Do not move the food processor whilst in operation.
Do not leave the food processor unattended when 

in use.
Do not place any part of the food processor in the 

dishwasher or microwave oven.
Do not process thin fluids such as water, milk, stock, 

juice, etc., above 500ml level in the processing bowl 

as this could result in overflow. To reduce the risk 

of overflow, always add drier or thicker ingredients 

to the processing bowl prior to adding fluids.
Do not place anything on top of the food processor 

when the lid is on, when in use and when stored
Keep  the  food  processor  clean.  Follow  the 

cleaning instructions provided in this book.


KFP100_FOODPROC_IB_FA.indd   3

29/5/09   4:27:53 PM

Summary of Contents for KFP100

























Reviews: