KAM KAV1300 Instruction Manual Download

Page: 9 / 12

SETTING THE MIC FREQUENCY

Press the main menu button until fb ex2 is displayed in the screen

Press the up/down arrow selection buttons to change setting ( range 1-6 )

This is effectively the mic tuning

This function is also available on the remote control press the main menu button

use the up/down buttons until the fb ex2 is displayed in the screen

then use the up/down buttons to select desired setting

REVERB TIME SET

Press the main menu select button until mic rev-t is displayed in the screen

Using the up/down buttons select the desired effect (range from 0-100 ms)

This function is also available on the remote control press the

main menu button use the up/down buttons until the

mic rev-t is displayed in the screen then use the up/down

buttons to select desired setting

SETTING THE MIC ECHO DELAY

Press the main menu button until mic pre-d is displayed in the screen

Using the up/down buttons select the desired effect (range from 0-250 ms)

This function is also available on the remote control press the

main menu button the until the mic pre-d displayed in the screen

then use the up/down buttons to select desired setting

2.Turn MENU button on remote control, press " " To
F.B TIME to set parameter value.

1Connect MIC, turn the frequency of relative MIC(MIC4,MIC5,MIC6,MIC7,MIC8) and press " " Of
REV LEVEL to set the frequency value to adjust level.

Effect lever set

2.Connect MIC,turn the frequency of relative MIC(MIC4,MIC5,
MIC6,MIC7,MIC8)to proper position and press "+/-" Of REV LEVEL
on remote control to adjust level.

MIC change frequency set

Main function of MIC change frequencfy set is to set MIC tune(range from 1-6 )

1.Press MASTER MENU On front panel, choose FB.EX*2 and press " " To set parameter value;
e.g,FB.EX2 6

2.Turn MENU botton on remote control,chooseFB.EX2
and press " " To set parameter value.

Operation introduction

2.Turn MENU button on remote control, press " " To
F.B TIME to set parameter value.

1Connect MIC, turn the frequency of relative MIC(MIC4,MIC5,MIC6,MIC7,MIC8) and press " " Of
REV LEVEL to set the frequency value to adjust level.

Effect lever set

2.Connect MIC,turn the frequency of relative MIC(MIC4,MIC5,
MIC6,MIC7,MIC8)to proper position and press "+/-" Of REV LEVEL
on remote control to adjust level.

MIC change frequency set

Main function of MIC change frequencfy set is to set MIC tune(range from 1-6 )

1.Press MASTER MENU On front panel, choose FB.EX*2 and press " " To set parameter value;
e.g,FB.EX2 6

2.Turn MENU botton on remote control,chooseFB.EX2
and press " " To set parameter value.

Operation introduction

Reverb time set

People can hear difference effect of room size from reverb time
Press MASTER MENU on front panel, choose MIC REVT and press to set parameter value;
E.g, MIC REV-T 100ms.

2.Press MENU on remote control, choose MIC REV-T
and press " " to set parameter value.

1.Press MASTER MENU on front panel, choose MIC PRE-D and press " " to set parameter value;
E.g, MIC PRE-D 100ms.

2.Press MENU on remote control, choose MIC PRE-D
and press " " to set parameter value.

MIC Echo delay set

Main function of echo delay set is to give you the great echo effect depends on the delay time you set.(range
from 2~250ms)

Operation introduction

Reverb time set

People can hear difference effect of room size from reverb time
Press MASTER MENU on front panel, choose MIC REVT and press to set parameter value;
E.g, MIC REV-T 100ms.

2.Press MENU on remote control, choose MIC REV-T
and press " " to set parameter value.

1.Press MASTER MENU on front panel, choose MIC PRE-D and press " " to set parameter value;
E.g, MIC PRE-D 100ms.

2.Press MENU on remote control, choose MIC PRE-D
and press " " to set parameter value.

MIC Echo delay set

Main function of echo delay set is to give you the great echo effect depends on the delay time you set.(range
from 2~250ms)

Operation introduction

Reverb time set

People can hear difference effect of room size from reverb time
Press MASTER MENU on front panel, choose MIC REVT and press to set parameter value;
E.g, MIC REV-T 100ms.

2.Press MENU on remote control, choose MIC REV-T
and press " " to set parameter value.

1.Press MASTER MENU on front panel, choose MIC PRE-D and press " " to set parameter value;
E.g, MIC PRE-D 100ms.

2.Press MENU on remote control, choose MIC PRE-D
and press " " to set parameter value.

MIC Echo delay set

Main function of echo delay set is to give you the great echo effect depends on the delay time you set.(range
from 2~250ms)

Operation introduction

Reverb time set

People can hear difference effect of room size from reverb time
Press MASTER MENU on front panel, choose MIC REVT and press to set parameter value;
E.g, MIC REV-T 100ms.

2.Press MENU on remote control, choose MIC REV-T
and press " " to set parameter value.

1.Press MASTER MENU on front panel, choose MIC PRE-D and press " " to set parameter value;
E.g, MIC PRE-D 100ms.

2.Press MENU on remote control, choose MIC PRE-D
and press " " to set parameter value.

MIC Echo delay set

Main function of echo delay set is to give you the great echo effect depends on the delay time you set.(range
from 2~250ms)

Operation introduction

SCHEMATIC DIAGRAM

OPERATION INSTRUCTIONS

Connect the mains supply and press the power button as

( pic 1)

The power led will light and the display welcome will appear

(pic2 )

The auto detect will appear ready to scan input devices

( pic 3 )

The input button will flash ready for you to select the desired input source or choose the auto scan function

Note: the value from left to right in the display is effect level-mic volume-music-volume see pic 4 above

OPERATION SELECT BUTTON

The input select button selects the desired input source there are 4 separate input choices

(bgm ,dvd,tv,vcr,)

and auto input detect

Press the input select button to choose input ie. Dvd your selection will be displayed on the display screen

This function is also available on the remote control pressing the

input select button Will change the input source and your selection

will be displayed in the screen

When no signal is being received when the auto detect function is

selected any signal detected will automatically be selected the

sensitivity of detection can be adjusted with the bgm adjuster

Schematic chart

MIC1

MIC6

MIC7

MIC8

BGM

VCR

DVD

SEVEN EQ

Cut low frequency

Left and right

balance output

MIC

volume

control

Music

volume

control

Output

frequency

control

MIC output R

Music output R

Assistant

output L

Assistant

output R

Anti whistle

Reverb

Echo proportion

Delay time

AUX output chose

MIC output L

Music ouput L

Mic L+Music L

MIC output R

Music output R

Mic R+Music R

DSP processor

Treble middle

bass

volume

control

Signal change

and

auto change

MIC direct signal

(L/R)assistant

line output

MIC output L

Music output L

Cut high frequency

Operation introduction

Begin

Note:

the value from left to right of picture4 means:"effect level" mic volume. music volume

Input volume chose(input)

INPUT button function is supply input siganl,have 4 separate input choice and auto check input
function,(BGM,DVD,TV,VCR and AUTO DETECT)

1.Press "INPUT" button, chosen signal display on the screen, for example, input DVD signal, display on the
point screen

2.Press "INPUT AUTO" button on remote control input
relative signal,auto check will display on the screen

3.When no signal input and choose auto signal,input level trimmed by BGM LEVEL;change to relative signal
channel auto as soon as machine check have signal input

Connect with power and press POWER button(as pic 1):power LED glittering and screen display"welcome"
(as pic 2),machine auto to check input channel(as pic3).Then "input" LED glittering; after checking machine
come into operation state, screen display(as pic4)

Operation introduction

Begin

Note:

the value from left to right of picture4 means:"effect level" mic volume. music volume

Input volume chose(input)

INPUT button function is supply input siganl,have 4 separate input choice and auto check input
function,(BGM,DVD,TV,VCR and AUTO DETECT)

1.Press "INPUT" button, chosen signal display on the screen, for example, input DVD signal, display on the
point screen

2.Press "INPUT AUTO" button on remote control input
relative signal,auto check will display on the screen

3.When no signal input and choose auto signal,input level trimmed by BGM LEVEL;change to relative signal
channel auto as soon as machine check have signal input

Operation introduction

Begin

Note:

the value from left to right of picture4 means:"effect level" mic volume. music volume

Input volume chose(input)

INPUT button function is supply input siganl,have 4 separate input choice and auto check input
function,(BGM,DVD,TV,VCR and AUTO DETECT)

1.Press "INPUT" button, chosen signal display on the screen, for example, input DVD signal, display on the
point screen

2.Press "INPUT AUTO" button on remote control input
relative signal,auto check will display on the screen

3.When no signal input and choose auto signal,input level trimmed by BGM LEVEL;change to relative signal
channel auto as soon as machine check have signal input

Operation introduction

Begin

Note:

the value from left to right of picture4 means:"effect level" mic volume. music volume

Input volume chose(input)

INPUT button function is supply input siganl,have 4 separate input choice and auto check input
function,(BGM,DVD,TV,VCR and AUTO DETECT)

1.Press "INPUT" button, chosen signal display on the screen, for example, input DVD signal, display on the
point screen

2.Press "INPUT AUTO" button on remote control input
relative signal,auto check will display on the screen

3.When no signal input and choose auto signal,input level trimmed by BGM LEVEL;change to relative signal
channel auto as soon as machine check have signal input

five

eight