SETTING THE MIC VOLUME
1.
Master mic volume control
2.
Mono mic input sockets from 1 - 6
3.
Individual mic volume controls from 1 - 8 adjust mic volumes to desired volume
Note: mic input 7 & 8 (balanced) are on rear of unit
This function is also available on the remote control using the mic / -buttons
FEEDBACK CONTROL
This function is to control the feedback response times on the microphones ( 20-80ms )
Press the master menu button until f.b time is displayed in the screen
Press the up/down arrows to select the required setting
This function is also available on the remote control using
the main menu button and then the up/down buttons
to select desired settings
SETTING THE REVERB LEVEL
The reverb level is set using the rev level button pressing the up/down button to increase or decrease the
amount of reverb ; set this to desired level this adjust the amount of reverb on all mic channels
This function is also available on the remote control press
the up/down buttons on the rev level
Operation introduction
MIC volume control
1.Input MIC,set sensitivity value for relative MIC(MIC1.MIC2,MIC3,MIC4,MIC5,MIC6,MIC7,MIC8),connect MIX4
as picture
2. Turn relative MIC frequency to proper position and turn MIC main volume knob to control music volume
3. Turn relative MIC volume to proper position(MIC1.MIC2.MIC3,MIC4,
MIC5,MIC6,MIC7,MIC8)and press-+ of MIC VOL on remote control to
control music volume
F.B TIME set
Main function of F.B TIME is to control feed back response time(20-80ms)
1.Press MASTER MENU button on front panel,then Press" " to F.B TIME to set parameter for example:
9
1
2
3
Operation introduction
MIC volume control
1.Input MIC,set sensitivity value for relative MIC(MIC1.MIC2,MIC3,MIC4,MIC5,MIC6,MIC7,MIC8),connect MIX4
as picture
2. Turn relative MIC frequency to proper position and turn MIC main volume knob to control music volume
3. Turn relative MIC volume to proper position(MIC1.MIC2.MIC3,MIC4,
MIC5,MIC6,MIC7,MIC8)and press-+ of MIC VOL on remote control to
control music volume
F.B TIME set
Main function of F.B TIME is to control feed back response time(20-80ms)
1.Press MASTER MENU button on front panel,then Press" " to F.B TIME to set parameter for example:
9
2.Turn MENU button on remote control, press " " To
F.B TIME to set parameter value.
1Connect MIC, turn the frequency of relative MIC(MIC4,MIC5,MIC6,MIC7,MIC8) and press " " Of
REV LEVEL to set the frequency value to adjust level.
Effect lever set
2.Connect MIC,turn the frequency of relative MIC(MIC4,MIC5,
MIC6,MIC7,MIC8)to proper position and press "+/-" Of REV LEVEL
on remote control to adjust level.
MIC change frequency set
Main function of MIC change frequencfy set is to set MIC tune(range from 1-6 )
1.Press MASTER MENU On front panel, choose FB.EX*2 and press " " To set parameter value;
e.g,FB.EX2 6
2.Turn MENU botton on remote control,chooseFB.EX2
and press " " To set parameter value.
Operation introduction
10
2.Turn MENU button on remote control, press " " To
F.B TIME to set parameter value.
1Connect MIC, turn the frequency of relative MIC(MIC4,MIC5,MIC6,MIC7,MIC8) and press " " Of
REV LEVEL to set the frequency value to adjust level.
Effect lever set
2.Connect MIC,turn the frequency of relative MIC(MIC4,MIC5,
MIC6,MIC7,MIC8)to proper position and press "+/-" Of REV LEVEL
on remote control to adjust level.
MIC change frequency set
Main function of MIC change frequencfy set is to set MIC tune(range from 1-6 )
1.Press MASTER MENU On front panel, choose FB.EX*2 and press " " To set parameter value;
e.g,FB.EX2 6
2.Turn MENU botton on remote control,chooseFB.EX2
and press " " To set parameter value.
Operation introduction
10
2.Turn MENU button on remote control, press " " To
F.B TIME to set parameter value.
1Connect MIC, turn the frequency of relative MIC(MIC4,MIC5,MIC6,MIC7,MIC8) and press " " Of
REV LEVEL to set the frequency value to adjust level.
Effect lever set
2.Connect MIC,turn the frequency of relative MIC(MIC4,MIC5,
MIC6,MIC7,MIC8)to proper position and press "+/-" Of REV LEVEL
on remote control to adjust level.
MIC change frequency set
Main function of MIC change frequencfy set is to set MIC tune(range from 1-6 )
1.Press MASTER MENU On front panel, choose FB.EX*2 and press " " To set parameter value;
e.g,FB.EX2 6
2.Turn MENU botton on remote control,chooseFB.EX2
and press " " To set parameter value.
Operation introduction
10
MUSIC VOLUME
1.
Rotary master volume control
2.
Master volume control is also available on the remote control
Note; maximum volume level is +63db
SETTING THE EQ & BALANCE
Press the master menu button until balance is displayed in the screen
The value 00 is the centre of left and right balance
Pressing the down button will adjust the balance to the left and pressing
the up button will adjust the balance to the right.
Set this to the desired setting
Press the master menu button until bass is displayed in the screen
The value 00 is a flat bass signal
Pressing the down button will decrease the bass signal
Pressing the up button will increase the bass signal
Set this to the desired setting
Press the master menu button until middle is displayed in the screen
The value 00 is a flat middle signal
Pressing the down button will decrease the middle signal
Pressing the up button will increase the middle signal
Set this to the desired setting
Press the master menu button until treble is displayed in the screen
The value 00 is a flat treble signal
Pressing the down button will decrease the treble signal
Pressing the up button will increase the treble signal
Set this to the desired setting
This function can also be carried out on the remote control using
The menu button to select the function and the up/down arrows
to adjust the settings
Operation introduction
Music volume set
1.Rotary main volume knob adjust music volume
2."-+" on "MUSIC VOLUME" of remote control
adjust volume
3.Maximal music volume is+63dB
Music tune set
1.Press button of MASTER MENU on the front panel.choose parameter(BASS,MIDDLE,TREBLE)then
press" " button of PARAMETER to set parameter value.for example to set BASS +10dB
2.Turn button MENU on remote control to choose
parameter (BASS,MIDDLE,TREBLE),then press
" " button to choose parameter
8
Operation introduction
Music volume set
1.Rotary main volume knob adjust music volume
2."-+" on "MUSIC VOLUME" of remote control
adjust volume
3.Maximal music volume is+63dB
Music tune set
1.Press button of MASTER MENU on the front panel.choose parameter(BASS,MIDDLE,TREBLE)then
press" " button of PARAMETER to set parameter value.for example to set BASS +10dB
2.Turn button MENU on remote control to choose
parameter (BASS,MIDDLE,TREBLE),then press
" " button to choose parameter
8
Operation introduction
Music volume set
1.Rotary main volume knob adjust music volume
2."-+" on "MUSIC VOLUME" of remote control
adjust volume
3.Maximal music volume is+63dB
Music tune set
1.Press button of MASTER MENU on the front panel.choose parameter(BASS,MIDDLE,TREBLE)then
press" " button of PARAMETER to set parameter value.for example to set BASS +10dB
2.Turn button MENU on remote control to choose
parameter (BASS,MIDDLE,TREBLE),then press
" " button to choose parameter
8
Operation introduction
Music volume set
1.Rotary main volume knob adjust music volume
2."-+" on "MUSIC VOLUME" of remote control
adjust volume
3.Maximal music volume is+63dB
Music tune set
1.Press button of MASTER MENU on the front panel.choose parameter(BASS,MIDDLE,TREBLE)then
press" " button of PARAMETER to set parameter value.for example to set BASS +10dB
2.Turn button MENU on remote control to choose
parameter (BASS,MIDDLE,TREBLE),then press
" " button to choose parameter
8
six
seven
