P a g e |
2 1
P a g e |
2 0
©2018 Kaivac, Inc. All Rights Reserved |
www.kaivac.com
Customer/Technical Support |
1-800-287-1136
3.3 s
PRay
-
and
-v
ac
o
PeRation
3.0 Operation
3.4 a
uto
v
ac
tm
o
PeRation
3.0 Operation
the autoVac
TM
feature is a walk-behind system for high speed cleaning of hard surface areas. it cleans as
well and as fast as a walk-behind or ride-on auto scrubber at a fraction of the cost.
after the unit has been filled with the appropriate
amount of water/solution, ensure that the orange
autoVac
TM
connector on the side of the cart is
connected in place.
lower the microfiber pad and wide-area squeegee
Head by lifting the orange strap on the rear handle to
unsnap it, and lower the pad and squeegee Head.
reattach with next button snap to hold
orange Strap in place.
to begin cleaning floor area with autoVac
TM
:
use thumb throttle to dispense solution
through the Spigot. Turn dial on Thumb
throttle to #2. increase if you need to
dispense solution at a faster rate.
TIP: TO uSe uP The SOluTIOn In The PAD, Turn
The ThuMb ThrOTTle TO Off APPrOxIMATely
50’ In ADvAnce Of fInIShInG The flOOr
.
CAU
TIO
N:
Kee
p in
OFF
pos
ition
whe
n no
t in
use
1
3
2
4
Aut
o V
ac
OFF
Walk back and forth across the area to be cleaned,
using a three point turn approach when reaching
turns, as detailed below.
once complete, lift the orange strap to raise the spreader
pad and squeegee Head and snap into place.
use included Vacuum tool to pick up any remaining liquids
or drips on the floor.
Walk forward
to end of area
being cleaned.
continue
turn. Overlap
previous pass.
pull back
and begin
turn.
begin turn.
the omniFlex
TM
spray-and-Vac system combines the 500 psi omniFlex
M
pump system with the wet Vacuum
and the trolley-bucket for extreme soil removal. it empowers workers to clean hygienically without touching
contaminated surfaces.
WArNiNg: DO NOT PUT
ChemiCAl iN TrOlley-
BUCKeT reSerVOir WheN
USiNg PUmP! DOiNg SO
Will CAUSe PrODUCT
DAmAge.
Tip
receptacle
cap
draw Tube
To prepare the cleaning chemical, make sure the
draw tube is inserted into the chemical jug. insert
the metering tip as shown (see metering tip
selection chart on the metering tip bag). then
screw the chemical cap onto the chemical jug
and make sure the clear chemical line is
connected to the chemical cap.
To prime the pump: squeeze brimer bulb 10 times
prior to initial startup, or if pump has been run dry
for any length of time.
operate the spray gun as shown. chemicals applied
in the low pressure setting only. chemicals must be
cleared from the Spray Line prior to High pressure
rinsing. to do this, turn oFF the chemical Valve,
then spray in low pressure settings for 15 seconds.
review control panel. make sure pump switch and
chemical Valve are in oFF position prior to plugging
in. if using with omniFlex
TM
Vacuum motor, plug in
the Vacuum cord into control panel receptacle.
plug in and press the black test button on the gFci
(ground Fault circuit interrupter), then red light
should turn off. then press the red reset button
and red Light should come on.
Hour Meter
Fan Spray
Low
pressure
High
pressure
pinpoint Spray
pump Switch
chemical Valve
