background image

KAIRAK 

 

Page 13 

 

 

  

 

- 13 - 

IM-ES-REV 5-09-06.doc5-09-06 

 

 
                                                                         

A Div of ITW FEG, LLC.

 

 

 

 

1-YEAR LABOR WARRANTY 

 

Kairak warrants that equipment manufactured by Kairak will be free from defects in 
material and workmanship for a period of 1-year beginning 30 days after ship date.  All work 
must be pre -approved by the factory to qualify for reimbursement under this warranty. 
Unapproved labor claims will not be paid. Note: t-stat and time clock adjustments are not 
covered under this warranty. 
 

1-YEAR PARTS WARRANTY 

 
Components such as compressors, fan motors, t-stats (ETC), time clocks, expansion valves, 
etc. shall be warranted for a period of 1-year beginning 30 days after ship date. Note:  
gaskets, filters, cutting boards, driers, sight glasses, and freon are not covered under this 
warranty. Kairak must be informed of the component failure and given the option to ship a 
replacement part or authorize purchase of the part locally by the service contractor. Parts 
utilized for emergency replacement and parts purchased locally by contractor shall be 
reimbursed at cost, an invoice of the purchased part must be supplied with the labor invoice. 
All defective parts must be returned to Kairak C.O.D. via UPS or common carrier. 
 

5-YEAR COMPRESSOR WARRANTY  

 

Compressor manufacturer warrants compressor components for a period of twelve months 
from the serial number manufacture date. Replacement compressors required during this 
period are to be acquired by over the counter exchange at the appropriate wholesaler. Kairak 
will warrant the labor to replace the compressor for the first year only. After the expiration 
of the compressor manufacturer warranty as indicated above, Kairak will warrant 

compressors only for a period not to exceed 4-years from the original start-up date. 

 Labor, tax, 

shipping, and miscellaneous parts will not be included. Please contact our Warranty 
Department for compressor replacement and procedures during this time. 
 
 

PLEASE NOTE: 

Contributing factors that impact refrigeration performance such as fixture doors and or 
drawers being left open, hot products such as soup being placed inside the reach-in box, 
fixture top insert pans being left out, improper equipment maintenance, debris such as plastic 
wrap covering coil openings, food not being removed from drain areas, are all considered 
maintenance and or improper usage will not be covered under warranty.   

 

Kairak Warranty/Service Department – (800) 833-1106 After Hours – (714) 870-9400 

 

500 S. State College Blvd., Fullerton, CA. 92831 

(Phone: 714-870-8661 Fax:  714-870-6473)

 

 

 

 

Summary of Contents for KRES














Reviews: