Kahn S4000 Integrale Installation, Operation And Maintenance Manual Download Page 26

Page: 26 / 34

Page 26

KAHN INSTRUMENTS, INC.

885 Wells Road, Wethersfield, CT 06109

Tel: 860-529-8643; Fax: 860-529-1895

E-mail: [email protected]

www.kahn.com

TECHNICAL SPECIFICATIONS

5.1

General

Accuracy - complete

system, nominal:

+/- 0.1

C. dewpoint - displayed.

+/- 1.0 % RH - displayed.

Cooling rate:

5 oC. / second (average).

Response speed:

Approx. 1 minute above 0

C dewpoint and 1 hour at

-60

C dewpoint. Variable between these limits.

Sensitivity:

0.01

Repeatability:

0.1

C. dewpoint.

Power supply:

90 to 260 Volts AC 50 - 60 Hz.

Power consumption:

Max. 250 VA.

Power Fuse:

3.15 Amp 250V 20 mm. Time delay.

Heat Pump Fuse:

3.15 Amp 250V 20 mm. Time delay.

Operating temperature:

0 to 40

C. Performance quoted at 21

C ambient.

Operating environment:

0 to 90% RH.

Dimensions (mm):

19" sub-rack. 133H (3U) x 511D.

Weight:

9.8 kg (21.6 lb ).

5.2

Sensor

Mirror cooling:

Three stage Peltier with forced air cooling.

Mirror:

Plated copper.

Dewpoint range:

-60 to +35

Cdp.

Summary of Contents for S4000 Integrale



































Search results

Summary of Contents for S4000 Integrale

Reviews:

Related manuals for S4000 Integrale

Brands by name

Popular brands

Kahn S4000 Integrale, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for S4000 Integrale

Reviews:

Related manuals for S4000 Integrale

Brands by name

Popular brands