background image

4. 

Unpacking the 

505DSP 

The carton contains the following items: 

505DSP Transceiver 

505CH 

Control 

Head 

Control Head Cable, 2.5 m. 

(8 

ft.) 

length 

Power 

Cable, 2.5  m. 

(8 

ft.) length 

Jumper Cable, 76 cm (2.5 

ft.) 

length 

2-port Junction Panel containing one 

HDE I 5  

and one DE9 connector w/6 

cm 

(2 

ft.) cable 

3.5" 

Installation Diskette 

Quick  Reference Chart 

Dynamic Microphone 
3.5 m m  

(I /8") 

Phone Jacks 

(3) 

Self-adhesive Rubber Feet (4) 
Spare Kachina Logo 
Control Head Mounting Screws 

(4) 

If your 

carton 

is 

missing any of the above items when received, 

your Dealer immediately. 

5.  Location 

General 

The 505DSP must be used indoors 

or 

in 

an enclosed vehicle.  The transceiver and 

control head are not weatherproof and 

must 

not 

be exposed 

to 

the elements 

or to 

temperatures 

exceeding 

to 

50°C. 

Transceiver 

The transceiver may be mounted up 

to 

23m (75 

ft.) 

away from the computer. 

Control cables approximately  2.5m 

(8 

ft.) in length are supplied standard with the transceiver 

while 7.6m and 23m 

(25 

and 75 

cable lengths may be purchased from Kachina. 

For 

bench 

or 

desk top use, the 

505DSP 

transceiver is designed 

to 

stand vertically 

or 

horizontally. 

Self-adhesive rubber 

feet 

are supplied and may be attached 

to 

either the side 

or 

bottom 

of 

the 

cabinet. 

spare Kachina logo 

is 

provided in case you wish 

to 

pivot the 

logo 

from 

the factory- 

supplied position. 

An accessory mounting bracket 

is 

available from Kachina in the event you 

wish 

to 

secure the 

transceiver 

to 

desk 

or 

wall 

or 

install 

in 

vehicle. 

If 

installing the transceiver in a vehicle, care 

should be taken 

to 

ensure that the radio is protected from the elements and 

not 

exposed 

to 

excessive shock 

or 

vibration.  Rubber shock mounts are available from Kachina.  Shock 

mounts 

should be considered mandatory if you have a harsh riding vehicle 

or 

expect 

to 

travel 

on 

rough 

roads, and are recommended 

for 

mobile installations 

in 

all cases. 

Control Head 

The 

505DSP 

is 

supplied 

with 

control head containing the main power switch 

and microphone, speaker, Morse key and phone jacks.  Cables 

are 

provided to install 

it 

in an 

Summary of Contents for 505DSP




















Reviews: