background image

13

14

Slide the sunshade lever upward to close 

the inner sunshade.

Slide the sunshade lever downward to 

open the inner sunshade.

Always operate using the sunshade lever, otherwise the parts 

may be damaged.

CAUTION!

CAUTION!

CAUTION! *Pinlock

®

 Original Insert Lens

Attach the Pinlock

®

Original Insert Lens after you made the shield to be 

adequately flat. The eccentric pin could be damaged.

Remove any dirt from the inside of the shield when attaching. Be very careful not 

to touch the anti-fog surface on the silicone seal side of the Pinlock

®

 Original 

Insert Lens.

Never use solvents such as benzine, thinners, gasoline, glass cleaners, or the like 

when cleaning because they can damage the material.

Never leave in locations that are 50°C or higher, near a heater, or to use anything 

that produces heat, such as a hair dryer or a flame when drying because of the 

risk to the material.

Use the Pinlock

®

 Original Insert Lens only with a dedicated shield.

If the area between the shield and Pinlock

®

 Original Insert Lens becomes 

foggy, or water has penetrated the area, remove the Pinlock

®

 Original Insert 

Lens and dry both the shield and the Pinlock

®

 Original Insert Lens thoroughly 

before re-attaching.

The silicone seal may stick to the shield, so regularly remove it to clean the 

Pinlock

®

 Original Insert Lens.

Beware that the Pinlock

®

 Original Insert Lens can become foggy when the chin 

ventilation is closed or when the wind shutter is used.

If the anti-fogging effect decreases or the shield is scratched, do not use it as 

it is. Replace it with a new one.

The silicone seal can enter your field of view depending on your riding 

position.

4

Inner Sunshade

Inner Sunshade

開閉レバー

Lever

—How to Open and Close—

To Open

Lever

Lever

Open

To Close

Lever

Lever

Close

Inner Sunshade

Inner Sunshade

WARNING: Opening/Closing lever

The sunshade lever must be slid completely when opening the inner sunshade 

because it can unexpectedly drops.

Do not use an inner sunshade in dark areas.

Open the inner sunshade when expecting change in temperature, because 

the inner sunshade can be fogged suddenly.

WARNING!

Summary of Contents for Ryuki

















Reviews: