KABI Accu Grease Gun 19.2V
PRODUCT SPECIFICATIONS
SAFETY INSTRUCTIONS
BLEEDING
1) Pull the piston rod out until it resists and connect the rubber seal by
turning the piston rod. Press the bleeding valve down, at the same
time pressing down on the piston rod.
2) When the cylinder is free of air, you should activate the grease gun a
few times. When the grease comes out without air pockets, release
the piston rod by turning it and pressing it gently into the grease
container.
Or:
1) Screw the container twice in reverse to bleed.
2) Pull the piston rod out until it resists and connect the rubber seal by
turning the piston rod, at the same time pressing down on the piston
rod.
3) When no more air comes out, screw the grease cylinder tightly on to
the grease gun and gently push the piston rod in.
INSPECTION, MAINTENANCE AND CLEANING
1. WARNING Make sure the switch is in the “Off” position, remove the
battery from the grease gun, and unplug the charger from the power
socket, before carrying out any inspection, maintenance or cleaning.
2. BEFORE EACH USE: Check the overall condition of the grease gun.
Check for defective, cracked or broken parts, battery leakage, dam-
aged hose, and anything else that could affect safe operation. In the
event of abnormal noise or vibration, the problem must be resolved
before further use. Never use damaged equipment.
3. BATTERY PRECAUTIONS: Never burn used batteries as they may
explode.Do not charge leaking batteries. Only a qualified service
technician should perform maintenance on the battery. Dispose of
the exhausted battery at your local battery dealer’s or at the local
recycling depot.
4. DAILY CARE: Use a dry, soft cloth to remove grease and dirt from the
exterior of the grease gun. Never use solvent to clean the grease gun.
5. STORAGE: Always remove the battery from the grease gun. Store the
grease gun and the detachable components in a clean, dry place, out
of reach of children.
Charger input
230V AC
Battery Output
19.2V
Battery capacity
2000 mAh.
Battery charging time
1 hour
Maximum working pressure
600 Bar (40 Bar tolerance)
Grease reservoir capacity
400g cartridges/500g bulk container
Minimum Flow
75 g/min at NLGI 2 (+20°C)
Hose
75 cm
Weight
2.8 kg
To avoid electric shock, fire and/or serious damage, the
following safety instructions should be followed carefully.
WORKING AREA
1. Do not use power tools in explosive atmospheres,
where flammable liquids, gases or dust are present.
Power tools can give off sparks, which can ignite the
materials.
2. Keep work area clean and well lit. Clutter can cause
accidents.
ELECTRICAL SAFETY
1. Avoid bodily contact with earthed surfaces such as
pipes or connections. The risk of electric shock is
increased, if your body is earthed.
2. Do not expose power tools to rain or wet areas. Water
in a power tool increases the risk of electric shock.
WARNING
Do not use the grease gun or battery in damp or wet
conditions.
Do not use the grease gun or the battery if it has been
dropped, damaged, left outdoors or immersed in water.
To avoid electric shock, do not operate the battery, plug
or grease gun, if your hands are wet.
Extreme pressure can cause nozzles or the hose to burst.
Use only approved hoses and follow the printed instruc-
tions and warnings.
CHARGING THE BATTERY
All new batteries for the grease guns are supplied with a 30% charge
from the factory, and it must be charged fully before use. A Li-Ion bat-
tery must not be stored in discharged condition. This can cause the bat-
tery to lose the ability to charge. A Li-Ion battery can not withstand large
temperature fluctuations (which can occur in service vans).
General charging of the battery
Start charging by inserting the battery in the charger. Connect the
charger to a power socket. Make sure the voltage is correct (230 V).
When charging is completed (approx. 60 min.), pull the charger out of
the power socket and remove the battery.
The battery charger has two light indicators:
•
• •
•
= when the battery is charging, both lights are on.
•
•
= when the battery is fully charged, only the green light is on. Pull
the charger out of the power socket, and remove the battery.
PLEASE NOTE: The temperature of the battery will increase during use.
Allow the battery to cool down to room temperature, before charging,
to obtain the best possible charge.
m
Use ONLY the supplied original charger to charge the battery.
CHANGING THE GREASE CATRIDGE
Dismantling the grease cartridge
1) Slowly pull the piston rod out until the groove becomes visible, and
tilt it carefully into the notch on the back cover of the grease cylinder.
2) Dismantle the grease cylinder and remove the old cartridge.
Attaching the grease cartridge
1) Remove the plastic cap on the new grease cartridge and insert it into
the grease cylinder.
2) Remove the seal. Make sure that there is no plastic debris or other
dirt that can cause grease blockage and destroy the return valve,
hose and nozzle.
3) Screw the grease cylinder tightly on to the grease gun. Gently loosen
the piston rod from the back plate and push the piston rod in slightly.
Conversion of the grease gun, to allow filling from bulk container
1) Dismantle the grease cylinder.
2) Unscrew the back plate and remove the piston rod with the collar.
3) Grasp the rubber seal between your thumb and forefinger and turn
the piston lip 180°.
4) Insert the piston rod in the cylinder, screw on the back plate and
replace the grease cylinder in the grease gun.
Filling the gun from bulk container
1) Stick the opening of the cylinder below the surface of the grease. The
cylinder must be perpendicular to the surface.
2) Slowly pull the piston rod out until the groove becomes visible, and
tilt it carefully into the notch on the back cover of the grease cylinder.
3) Screw the grease cylinder tightly on to the grease gun
4) Gently loosen the piston rod from the back plate and push the piston
rod in.
KF720-C1 incl. 1 Lithium-Ion battery
KF720-D1 incl. 2 Lithium-Ion batteries
m
