background image

5

X-09 L

OCK

 S

ETUP

Setting up the X-09 lock for operation involves both the operating mode and the 
combination(s). 

Note: 

The lock is shipped preset to operate in the Single Combination Mode 

with a factory combination of 50-25-50. 

Before you can set a new combination, you must select and set a mode of operation. The 
X-09 has three modes of operation:

Single Combination Mode:

 The X-09 will open when one three-number combination 

is successfully dialed.

Dual Combination Mode:

 Two separate combinations are required to open the X-09. 

Either combination may be dialed fi rst; however, the operator must begin entering the 
second combination within 40 seconds of completing the fi rst combination.

Supervisory/Subordinate Mode or Super/Sub Mode:

 Two separate combinations 

are required to open the lock, with the Supervisory Combination controlling access 
of the Subordinate Combination.  The Supervisory Combination must be entered 
fi rst to 

U

n

L

ock (

UL

) the lock. Once the Supervisory Combination has been entered, 

the Subordinate Combination can be used to open the lock at any time during this 
“unlocked” state. The Supervisory Combination can be entered again to disable lock 
access - 

L

ock 

U

p (

LU

). In this state the Subordinate Combination will no longer open 

the lock.

SET OPERATING MODE AND CHANGE COMBINATIONS

Use the Change Key (Figure 2) provided with your X-09 to set the desired operating mode 
and combinations.  If at any time during the process you see the Key and Lightning Bolt 
symbols displayed, stop the sequence and return to Step 4. If at any time after you start the 
change key process, you see only a Lightning Bolt symbol displayed, stop the sequence, 
reinsert the change key, and return to Step 4.

Note: 

The lock serial number may be used to complete this process if the 

current combination has been lost or forgotten and if you can gain access 
to the back of the lock.

 

Using the serial number for this procedure will not open 

the lock. It will only allow you to set the new operating mode and combination(s). 
When using the serial number to change the combination, you must fi rst create an 

error by dialing an incorrect combination. 

If you have not read the section on “Dialing the X-09” and “Opening the X-09 (Factory 
Combination)”, it is important that you do so before proceeding.

Note: 

Use the preset 

factory combination

 of 

50-25-50 

to open the lock the fi rst 

time. If the container is already open, you may skip Step 1. 

1.  Open the lock by dialing the current combination(s) and retracting the bolt. 
 

Then remove the container dust cover to gain access to the change key holes on the 
back of the lock.

Fig. 2 - Change Key

Summary of Contents for 1F


















Reviews: