background image

UNCTION

5. Touch power sign again to clear the screen. Touch light button to validate. 

To check time, touch light button.

Adjust to desired period of delay of timer by touching(-) or(+) button quickly(1-15minutes).

Timer reaches 0, the blower will shut off.

While the range hood is on and the blower is running in normal mode, touch 

will be DE-ACTIVATED 

1.POWER:Once"POWER" button is touched,all other functions

Importance Notice:

A.    A

CTIVATING 

N

ORMAL 

B

LOWER 

F

:

While the range hood is off, 
                    Touch 

(+) to start from lowest speed, F1

                   

Touch 

(-) to start from Highest speed, F4

Touch (+) or (-) again to change the blower speed as indicated in LCD panel

B.    Activating Light Function:

Touch 

Light 

button to turn the lights on or off. 

C.    Activating Power-Off Delay Function:

1.

Power-Off Delay 

button to activate delay off timer. 

2.

3.

Display screen will show flashing clock if timer is working.

E.    Changing the clock (only available in some models)

          While the blower is off:

          1. Touch power sign once. The hour indicator will be flashing.
          2. Use (+) or (-) to adjust to the desired hour.
          3. Touch power sign again for the “minutes”. Indicator will be flashing.
          4. Use (+) or (-) to adjust to desired minutes.
         
           

Delay

Power on/off

Baffle Installation Side View

                       

Step 10: Install baffle filters

Install baffle filters; refer to picture at left for the following three steps: 

1.Angle baffle filter toward back of hood. 
2.Lift a baffle filter up above horizontal level. 

3.

Slide forward into slot behind the front of hood.

4.

Slide the installed baffle filter to either left or right until it stops.

5.

Repeat step 1 to 4 to install the next ones, make sure you slide to opposite direction from 

the previous installed filter.

To remove the baffle, please reverse the process. 

NOTE: The middle filter has to be installed last where it should be taken out first when you 
want to remove other filters.

STEP 9: INSTALL OIL TUNNEL OR OIL CONTAINER (NOT AVAILABLE FOR ALL MODELS)

Drop oil tunnel into recess support near rear of hood. Refer to the left picture

Oil Tunnel 
Side View

Summary of Contents for K1039








Reviews: