background image

 
INSTALL MOUNTING PLATE AND ANGLE IRON 

 

1. 

Fix  the  instruction  paper  onto  the  ceiling.  Drill 
holes as the paper show. 

2. 

Put the drywall anchors into the holes and pick out 
the  mounting  plate  and  use  12  pcs  mounting 
screws  to  fix  the  plate  onto  the  ceiling.(If  for 
concrete  ceiling,  pls  use  the  8  pcs  of  explode 
screws).   

3. 

Put  out  the  8  pcs  of  angle  iron,  use  8  pcs  of 
mounting screws(4*14mm) with washers and nuts 
to fixe 4 pcs angle iron onto the mounting plate. 

4. 

Adjust  the  height  X  of  the  chimney(  as  shown  on 
the  picture  1),  use  16  pcs  of  munting 
screws(4*14mm) with washers and nuts to fixe the 
other 4 pcs angle iron onto the angle irons which 
have been installed. 

 

 

 

INSTALL THE DUCTWORK 
 

NOTE: To reduce the risk of fire, use only metal ductwork. 

 

1.  Deside  where  the  ductwork  will  run  between  the  hood  and  the 

outside. 

2.  A  straight,  short  duct  run  will  allow  the  hood  to  perform  most 

efficiently. 

3.  Let  the  one  side  of  the  duct  go  outside  through  the  hole  of  6.7’’  as 

shown. 

 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for K1023














Reviews: