background image

Pro Cube                                                                                                                                                                                        

K+R Performance Engineering, Inc.

 

 

 

Release them both when your tree is activated.  One hand will be a little faster than the other, possibly 
giving you a few thousandths better reaction time. 

 

If you need an additional timer, contact tech support and arrange for an economical upgrade.

  

 
TROUBLESHOOTING

 

 

 

The front panel includes an indicator light for each output.  These lights give you direct indication of 

whether the corresponding output is off or on.  A flashing light indicates a shorted or overloaded output.  If 
this  occurs,  first  disconnect  the  output  and  cycle  the  unit  again,  watching  the  indicators.    If  the  output 
operates normally while disconnected then the problem is in your wiring or equipment. 
 

If the unit operates erratically when the engine is running, and normally when the engine is off, check 

for sources of electrical interference.  The 

PRO-CUBE 

Ò

 

is designed to tolerate extreme interference but 

the ignition coil, spark plug wires, and ignition unit are powerful sources of RF interference and a minimum 
distance  of  12”  is  recommended.    If  you’re  using  solid  core  spark  plug  wires,  replace  them  with  an  RF 
suppressive spiral core wire set. 
 

TECHNICAL SUPPORT

 

 
Contact:

 

K

+

R Performance Engineering, Inc. 

Telephone:    423-614-7778 
 
 

WARRANTY 

 

 

We  at  K&R  Performance  Engineering  Inc.  warrant  to  the  original 

purchaser the products manufactured by us to be free from defects in material 

and workmanship under normal use and service, for which it was intended, but 

only  if  it  has  been  properly  installed  and  operated.  Our  obligation  under  this 

warranty  shall  be  limited  to  the  repair of any product or products which may 

thus prove defective under normal use and service, for which it was intended, 

within two (2) years from the date of installation by the original purchaser, and 

which  our  examination  shall  disclose  to  our  satisfaction  to  be  thus  defective. 

Any  defect  affecting  operation  of  the  unit  will  be  repaired  at  no  charge.  You 

will be billed only for shipping. Damage caused by severe vibration and metal-

to-case  contact  or  restricted  movement  due  to  improper  mounting  is  NOT 

covered. 

 

THIS  WARRANTY  IS  EXPRESSLY  IN  LIEU  OF  ALL  OTHER 

WARRANTIES  EXPRESSED  OR  IMPLIED  INCLUDING  THE 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE AND 

OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, AND 

WE NEITHER ASSUME, NOR AUTHORIZE ANY OTHER PERSON TO 

ASSUME  FOR  US,  ANY  OTHER  LIABILITY  IN  CONNECTION  WITH 

THE  SALE  OF  THIS  PRODUCT.    THIS  WARRANTY  SHALL  NOT 

Summary of Contents for PRO-CUBE













Reviews: