background image

6

FUNC key, and then press other keys to realize the second functions 

silk-screened under the button. "FUNC+ Keypad name" is to be used 

in the following operating instruction.

16. 

ROGER BEEP or BEEP FUNCTION

(1)

RB

Press "RB" key to enable "ROGER BEEP" function with "RB" icon 

appearing on LCD display. Press the key repeatedly to switch on/off 

the function.
When RB function is enabled, the radio will automatically transmit the 

audio signal at the end of your transmission. The listener can note 

easily that your transmission is over through the signal.

(2)

FUNC+RB

Press FUNC+RB to realize BP Function. It is a prompting function with 

"BP" icon appearing on LCD display. Speaker would emit a BEEP for 

prompting when press any key. press FUNC+RB repeatedly to switch 

on/off the function.

17. 

 NB/ANL or LOCK

(1)

Press NB/ANL key to enable NB/ANL function with "NB/ANL" icon 

appearing on the LCD display. Press the key repeatedly to switch on/

off the function.
Noise Blanker/Automatic Noise Limiter. These filters allow reducing 

back ground noises and some reception interferences.

(2)

FUNC+NB/ANL

Press FUNC+NB/ANL to realize the Keyboard Lock function. When 

this function is enabled, all keys are invalid except PTT, BAND 

SWITCH, and MODE SWITCH. When pressing any key except PTT, 

BAND SWITCH, MODE SWITCH, the LOCK icon will display on the 

LCD. These situations indicate that the keyboard has been locked.  

Press FUNC+NB/ANL repeatedly to switch on/off the function.

18. 

DW or LCD OFF

(1)

The DW (dual watch) function allows automatic alternate 

monitoring of two channels. Refer to the following procedures to 

enable this function. 
To enable the DW function, firstly turn the SQ control clockwise 

until the background noise is cut out. Select the first channel to be 

monitored by using the CHANNEL SELECTOR knob or the channel 

selector keys on the microphone. Press the DW key and the DW icon 

will flash on the LCD display. Secondly, follow the above procedures 

to select second channel to be monitored. Finally, press the DW key 

again and the two monitoring channels will be alternately indicated on 

the LCD. Radio will automatically start monitoring (scanning) the two 

channels. When a signal is detected on one of the channels, scanning 

stops and it is possible to listen the communications on that channel. 

Press PTT to transmit on this channel. If there is no transmission 

or detected signal on that channel within 5 seconds(time to resume 

scanning can be programmed by PC software), radio will resume 

scanning. When the DW function is enabled, the DW icon appears on 

the LCD. To exit the DW function, press the DW key or the PTT key. 
The scan Type above is the SQ mode under SCA Selection in 

Function Menu. If TI mode is selected and valid signal is detected, the 

radio would still start scanning when it is time to resume scanning, 

whether there is signal or not in current channel.

(2)

FUNC+DW

When this function is enabled, LCD display would be switched OFF 

(LCD OFF).
Repeat this operation to switch ON/ OFF the function.

19. 

SCAN or SCAN LIST

(1)

SCAN

Automatic Scanning of busy channels.
Press the SCAN key to enable the SCAN function. Before enabling the 

SCAN function, firstly turn the SQ control clockwise till the background 

noise is cut out. Then press the SCAN key, radio will automatically 

scan all channels continuously in the scan list and the SC icon will 

appear on the LCD. 
When a signal is detected on a channel, scanning stops on this 

Summary of Contents for DX-5000 PLUS


















Reviews: