JVC UX-L36V Page 16 Service Manual Download

Page: 16 / 89

1-16

UX-L46V/UX-L36V

Remove the two screws

attaching the video board

assembly and the CD servo board at the bottom of
the CD mechanism assembly.

Disconnect the card wire from connector CN101 on
the video board assembly.
Move the video board assembly forward to release
the joint

, and remove.

Disconnect the card wire from connector CN606 on
the CD servo board. Turn over the CD servo board
as shown in Fig.3 and put aside temporarily.

Solder the shorting round on the pickup board in the
CD pickup section.

Disconnect the card wire from connector CN601 and
the wire from CN801 on the CD servo board.

Removing the CD servo board

(See Fig.3~5)

Solder the shorting round before disconnecting
the card wire extending from the pickup. If
you do not follow this instruction, the pickup
may be damaged.

CAUTION:

When reassembling, make sure to unsolder
the shorting round after connecting the card
wire from the pickup to the connector.

CAUTION:

The video board assembly can be
removed solely. To remove the video
board, see Fig.1 and 2.

REFERENCE:

Fig.5

CD servo board

CN601

CN801

CD pickup

Pickup board

Shorting round

(Soldering)

Fig.4

CD servo board

CN801

CN606

CN652

CN651

CN601

Fig.3

Video

board assembly

Joint a

CN101

Summary of Contents for UX-L36V


























































































Search results

Summary of Contents for UX-L36V

Reviews:

Related manuals for UX-L36V

Brands by name

Popular brands

JVC UX-L36V, Service Manual

Search results

Summary of Contents for UX-L36V

Reviews:

Related manuals for UX-L36V

Brands by name

Popular brands