JVC MX-K5 Service Manual Download Page 9

Page: 9 / 73

MX-K5/MX-K6

Prior to performing the following procedure, remove
the metal cover and the CD changer unit.

Remove the four screws I attaching the heat sink
cover on the back of the body. Remove the heat sink
cover.

Remove the four screws J attaching the heat sink &
AMP board to the rear panel on the back of the body.

Remove the two screws K attaching the speaker
terminal to the rear panel on the back of the body.

Disconnect the card wire from connector ACW1 &
the harness from connector ACW2 on the AMP
board. (See Fig.11)

After moving the heat sink upward, remove the
claws. Then pull out the heat sink & AMP board

Removing the heat sink & AMP board

(See Fig.14 and 15)

Prior to performing the following procedure, remove
the metal cover and CD changer unit.

Disconnect the card wire from connector CON01 on
the tuner board.

Remove the two screws L attaching the tuner pack.

Removing the tuner pack

(See Fig.15 and 16)

Prior to performing the following procedure, remove
the metal cover, CD changer unit, heat sink & AMP
board and tuner pack.

Remove the four screws M attaching the rear panel.

Removing the rear cover

(See Fig.17)

Fig.14

Fig.15

Fig.16

Fig.17

Rear panel

Heat sink

cover

Heat sink

Speaker terminal

Tuner terminal

Main board

Tuner board

CON01

Summary of Contents for MX-K5










































































Search results

Summary of Contents for MX-K5

Reviews:

Related manuals for MX-K5

Brands by name

Popular brands

JVC MX-K5, Service Manual

Search results

Summary of Contents for MX-K5

Reviews:

Related manuals for MX-K5

Brands by name

Popular brands