background image

Sleeve

Cubierta

Manchon

Trim plate

Placa de guarnición

Plaque d’assemblage

Remote controller

Control remoto

Télécommande

Rubber cushion

Cojín de goma

Amortisseur en caoutchouc

Mounting bolt (M5 x 20 mm)

Perno de montaje (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Lock nut (M5)

Tuerca de seguridad (M5)

Ecrou d’arrêt (M5)

Washer (ø5)

Arandela (ø5)

Rondelle (ø5)

Removing the unit

• Before removing the unit, release the rear section.

1

Remove the trim plate.

2

Insert the 2 handles into the slots, as shown. Then, while gently
pulling the handles away from each other, slide out the unit.
(Be sure to keep the handles after installing it.)

Extracción de la unidad

• Antes de extraer la unidad, libere la sección trasera.

1

Retire la placa de guarnición.

2

Inserte las 2 manijas entre las ranuras, como se muestra.
Luego, separe gentilmente las manijas y extraiga la unidad.

(Asegúrese de conservar las manijas después de
instalarlo.)

Retrait de l’appareil

• Avant de retirer l’appareil, libérer la section arrière.

1

Retirer la plaque d’assemblage.

2

Introduire les deux poignées dans les fentes, comme montré.
Puis, tout en tirant doucement les poignées écartées, faire
glisser l’appareil pour le sortir. (S’assurer de conserver les
poignées après l’installation de l’appareil.)

2

1

Parts list for installation and connection

The following parts are provided with this unit.
After checking them, please set them correctly.

Lista de piezas para instalación y conexión

Con esta unidad se suministran las siguientes piezas.
Después de inspeccionarlas, colóquelas correctamente.

Liste des pièces pour l’installation et
raccordement

Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.

• When using the optional stay
• Cuando emplea un soporte opcional
• Lors de l’utilisation du hauban en option

• When installing the unit without using the sleeve
• Instalación de la unidad sin utilizar la cubierta
• Lors de l’installation de l’appareil sans utiliser de manchon

In a Toyota for example, first remove the car radio and install the unit in its place.

En un Toyota por ejemplo, primero extraiga la radio del automóvil y luego instale la unidad en su
lugar.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

CR2025

Battery

Pila

Pile

Handles

Manijas

Poignées

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the
battery’s negative terminal and make all electrical connections
before installing the unit. If you are not sure how to install this unit
correctly, have it installed by a qualified technician.

Note:
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems
. If your vehicle does not have this system, a
voltage inverter is required, which can be purchased at JVC car
audio dealers.
• Replace the fuse with one of the specified rating. If the fuse blows

frequently, consult your JVC car audio dealer.

• If noise is a problem...

This unit incorporates a noise filter in the power circuit. However,
with some vehicles, clicking or other unwanted noise may occur.
If this happens, connect the unit’s rear ground terminal (See
connection diagram.) to the car’s chassis using shorter and thicker
cords, such as copper braiding or gauge wire. If noise still persists,
consult your JVC car audio dealer.

• Maximum input of the speakers:

For KD-LX300: Maximum input of the speakers should be more
than 50 W at the rear and 50 W at the front, with an impedance
of 

 to 8 

.

For KD-LX100: Maximum input of the speakers should be more
than 45 W at the rear and 45 W at the front, with an impedance
of 

Ω 

to 8 

.

• Be sure to ground this unit to the car’s chassis.
• The heat sink becomes very hot after use. Be careful not to touch

it when removing this unit.

CONEXIONES ELECTRICAS

Para evitar cortocircuitos, recomendamos que desconecte el
terminal negativo de la batería y que efectúe todas las conexiones
eléctricas antes de instalar la unidad. Si usted no está seguro de
cómo instalar correctamente la unidad, hágala instalar por un
técnico cualificado.

Nota:

Esta unidad está diseñada para funcionar con 

12 V de CC, con

sistemas eléctricos de masa NEGATIVA

. Si su vehículo no posee

este sistema, será necesario un inversor de tensión, que puede
ser adquirido en los concesionarios de JVC de equipos de audio
para automóviles.
• Reemplace el fusible por uno con la corriente especificada. Si

el fusible se quemase frecuentemente consulte con su
concesionario de JVC de equipos de audio para automóviles.

• Si el ruido fuese un problema...

Esta unidad tiene un filtro de ruido en el circuito de alimentación.
Sin embargo, en algunos vehículos, pueden producirse
chasquidos u otros ruidos indeseados. En tal caso conecte el

terminal de tierra posterior

 (Véase diagrama de conexión.) del

receptor al chasis del automóvil, utilizando cordones más
gruesos y cortos tales como alambre de cobre trenzado o de
grueso calibre. Si el ruido persiste, consulte a su concesionario
de JVC de equipos de audio para automóvil.

• La entrada máxima de los altavoces:

Para KD-LX300: La entrada máxima de los altavoces traseros
debe ser mayor de 50 W y la de los delanteros de 50 W, con una
impedancia de 

 a 8 

.

Para KD-LX100: La entrada máxima de los altavoces traseros
debe ser mayor de 45 W y la de los delanteros de 45 W, con una
impedancia de 

 a 8 

.

Asegúrese de conectar esta unidad a tierra en el chasis del
automóvil.

• El sumidero térmico estará muy caliente después del uso.

Asegúrese de no tocarlo al desmontar esta unidad.

RACCORDEMENTS ELECTRIQUES

Pour éviter tout court-circuit, nous vous recommandons de
débrancher la borne négative de la batterie et d’effectuer tous les
raccordements électriques avant d’installer l’appareil. Si l’on n’est
pas sûr de pouvoir installer correctement cet appareil, le faire
installer par un technicien qualifié.

Remarque:
Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 V à masse NEGATIVE. Si votre véhicule n’offre pas
ce type d’alimentation, il vous faut un convertisseur de tension,
que vous pouvez acheter chez un revendeur d’autoradios JVC.

Remplacer le fusible par un de la valeur précisée. Si le fusible
saute souvent, consulter votre revendeur d’autoradios JVC.

Si le bruit est un problème...
Cet appareil incor pore un filtre de bruit dans le circuit
d’alimentation. Cependant, avec certains véhicules, quelques
claquements ou autres bruits non désirés risquent de se produire.
Si cela arrive, raccorder la borne arrière de masse de l’appareil
au châssis de la voiture (voir le schéma de raccordement) en
utilisant des cordons les plus gros et les plus courts possibles
telle qu’une barre de cuivre ou une tresse. Si le bruit persiste,
consulter votre revendeur d’autoradios JVC.

La puissance admissible des enceintes:
Pour le KD-LX300: La puissance admissible des enceintes doit
être supérieure à 50 W à l’arrière et à 50 W l’avant, avec une
impédance de 

Ω 

à 8 

.

Pour le KD-LX100: La puissance admissible des enceintes doit
être supérieure à 45 W à l’arrière et à 45 W l’avant, avec une
impédance de 

Ω 

à 8 

.

• S’assurer de raccorder la mise à la masse de cet appareil au

châssis de la voiture.

Le dissipateur de chaleur devient très chaud après usage. Faire
attention de ne pas le toucher en retirant cet appareil.

Power cord

Cordón de alimentación

Cordon d’alimentation

Heat sink

Sumidero térmico

Dissipateur de chaleur

Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If
longer screws are used, they could damage the unit.
Nota:

 Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de

6 mm de longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.

Remarque:

 Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis

d’une longueur de 6 mm. Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Flat type screws (M5 x 6 mm)*

Tornillos tipo plano (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Bracket*

Ménsula*

Support*

* Not included with this unit.

* No suministrado con esta unidad.

Non fourni avec cet appareil.

Flat type screws (M5 x 6 mm)*

Tornillos tipo plano (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Fire wall

Tabique a prueba de incendios

Cloison

Stay (option)

Soporte (opción)

Hauban (en option)

Lock nut

Tuerca de seguridad

Ecrou d’arrêt

Mounting bolt

Perno de montaje

Boulon de montage

Screw (option)

Tornillo (opción)

Vis (en option)

Dashboard

Tablero de instrumentos

Tableau de bord

Trim plate

Placa de guarnición

Plaque d’assemblage

Handle

Manija

Poignée

Sleeve

Cubierta

Manchon

Washer

Arandela

Rondelle

Bracket*

Ménsula*

Support*

Pocket

Compartimiento

Poche

Summary of Contents for KD-LX300











































































Reviews: