Typical connections
Before connecting:
Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
Purple
Purple with black stripe
Green
Green with black stripe
Gray
Gray with black stripe
White
White with black stripe
A
ELECTRICAL CONNECTIONS
To the automatic antenna if any
(250 mA max.)
To the remote lead of other equipment (200 mA max.)
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
Right speaker (rear)
Left speaker (rear)
Right speaker (front)
Left speaker (front)
*
2
Before checking the operation of this unit prior to installation,
this lead must be connected, otherwise power cannot be
turned on.
15 A fuse
Line out (see diagram )
Rear ground terminal
*
1
Not supplied for this unit.
Ignition switch
Fuse block
Black
Red
Yellow
*
2
Blue
Connecting the external amplifiers and/or subwoofer
You can connect amplifiers to upgrade
your car stereo system.
• Connect the remote lead (blue with
white stripe) to the remote lead of
the other equipment so that it can be
controlled through this unit.
•
Disconnect the speakers from this
unit, connect them to the amplifier.
Leave the speaker leads of this unit
unused.
– The line output level of this unit is
kept high to maintain the hi-fi sounds
reproduced from this unit.
When connecting an external
amplifier to this unit,
turn down the
gain control on the external amplifier
to obtain the best performance from
this unit.
*
3
Firmly attach the ground wire to the metallic
body or to the chassis of the car—to the place
uncoated with paint (if coated with paint,
remove the paint before attaching the wire).
Failure to do so may cause damage to the unit.
B
Rear speakers
Remote lead
Remote lead (Blue with white stripe)
To the remote lead of other equipment or automatic
antenna if any
Y-connector (not supplied for this unit)
Front speakers
Subwoofer
JVC Amplifier
JVC Amplifier
To CD changer or another external component (see diagram )
To subwoofer (see diagram )
To car light control switch
To cellular phone system
Blue with white stripe
Orange with white stripe
Brown
JVC Amplifier
2
Connecting the external components
C
CD changer, Apple iPod®, or JVC D. player
CAUTION:
Before connecting the external
components, make sure that the unit is
turned off.
CD changer jack
JVC CD changer
• Set “Changer” for the external input setting (see page 18 of the INSTRUCTIONS.)
You can connect these components as illustrated below. The iPod
*
5
or D. player can be
connected using an interface adapter (not supplied)—KS-PD100 (for iPod) or KS-PD500
(for D. player).
Apple iPod (separately
purchased)
JVC D. player (separately
purchased)
or
Other external component
CD changer jack
External component
External component
*
7
Line Input Adapter KS-U57 (not supplied for this unit)
*
8
AUX Input Adapter KS-U58 (not supplied for this unit)
3.5 mm stereo mini plug
*
5
iPod is a trademark of Apple Computer, Inc.,
registered in the U.S. and other countries.
*
6
Connecting cord supplied for your CD
changer
• Set “Ext In” for the external input setting (see page 18 of the INSTRUCTIONS.)
*
4
Signal cord (not supplied for this unit)
Front speakers
Antenna connector
Instal1-2_KD-G824_[UI]f.indd 2
Instal1-2_KD-G824_[UI]f.indd 2
12/29/05 3:24:39 PM
12/29/05 3:24:39 PM
