background image

3

B

 

Connecting the parking brake wire

When installing the monitor in a location where it can be seen by the driver

Connect the parking brake wire to the parking brake system built in the car.

When installing the monitor in a location where it cannot be seen by the driver

Connect the parking brake wire to metallic body or chassis of the car.

 

Connecting the crimp connector

C

Parking brake wire (light green)

To metallic body or chassis of the car

Parking brake switch (inside the car)

Parking brake

Parking brake wire (light green)

To external components (see diagram   )

Light green

VIDEO OUT

(see diagram  )

DIGITAL OUT

(see diagram  )

A

To parking brake, metallic body or chassis of the car

Before connecting:

 Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.

The leads of the power cord and those of the connector from the car body may be different in color.

1

  Connect the colored leads of the power cord in the order specified in the illustration below.

2

  Connect the antenna cord.

3

  Finally connect the wiring harness to the unit.

15 A fuse

Black

Blue with white stripe

Red

Yellow 

*

2

To metallic body or chassis of the car

Ignition switch

Fuse block

To an accessory terminal in the fuse block

To the remote lead of other equipment (200 mA max.)

To a live terminal in the fuse block connecting to the car battery 
(bypassing the ignition switch) (constant 12 V)

*

1

  Not supplied for this unit.

*

2

  Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

Line out (see diagram 

 

)

Rear ground terminal

Left speaker (front)

Right speaker (front)

Left speaker (rear)

Right speaker (rear)

Purple

Purple with black stripe

Green

Green with black stripe

Gray

Gray with black stripe

White

White with black stripe

Wire connecting the battery and the parking brake switch.

Attach the parking brake wire to this point.

Contact the metallic part of the crimp to the wires inside.

Pinch the crimp firmly.

 

Typical connections

LINE IN

For KD-DV5304/KD-DV5303 (see diagram   )

ELECTRICAL CONNECTIONS

Antenna terminal

To the automatic antenna if any (250 mA max.)

Blue

Instal3-4_DV5304_002A_pre.indd   3

Instal3-4_DV5304_002A_pre.indd   3

12/5/06   11:23:55 AM

12/5/06   11:23:55 AM

Summary of Contents for KD-DV5304

Page 1: ...assis again after installation Notes Replace the fuse with one of the specified rating If the fuse blows frequently consult your JVC car audio dealer It is recommended to connect to the speakers with maximum power of more than 50 W both at the rear and at the front with an impedance of 4 Ω to 8 Ω If the maximum power is less than 50 W change AMP GAIN setting to prevent the speakers from being dama...

Page 2: ... 8 mm long screws If longer screws are used they could damage the unit Install the unit at an angle of less than 30 TROUBLESHOOTING The fuse blows Are the red and black leads connected correctly Power cannot be turned on Is the yellow lead connected No sound from the speakers Is the speaker output lead short circuited Sound is distorted Is the speaker output lead grounded Are the terminals of L an...

Page 3: ...rd 3 Finally connect the wiring harness to the unit 15 A fuse Black Blue with white stripe Red Yellow 2 To metallic body or chassis of the car Ignition switch Fuse block To an accessory terminal in the fuse block To the remote lead of other equipment 200 mA max To a live terminal in the fuse block connecting to the car battery bypassing the ignition switch constant 12 V 1 Not supplied for this uni...

Page 4: ...nna if any Front speakers Required connections for DVD playback Audio video control amplifier or the decoder compatible with the multichannel digital sources KV MR9010 9 INCH WIDESCREEN MONITOR 3 Digital optical cable 3 Apple iPod JVC D player CD changer jack You can connect these components as illustrated below The iPod or D player can be connected using an interface adapter not supplied KS PD100...

Reviews: