background image

2

AC IN

AUDIO

L

OUT

R

RGB A

AUDIO

IN

REMOTE

RS-232C

WIRED

MAKE

AUDIO

L

OUT

R

REMOTE

RS-232C

WIRED

MAKE

RGB A

AUDIO

IN

This Video Input unit allows the Plasma Display Monitor GM-V42PCE, GM-V42PCEG and GM-V42PCEB to cope with video signals
— Video (composite), S-video(Y/C), and Component/RGB — and audio signals.

SAFETY PRECAUTIONS

This installation requires technical skills and electrical acknowledgment. It is very dangerous to install this kit by yourself.
For installation, consult JVC authorized dealer.

Some of the parts, such as rear panel and blank panel, are very heavy and have keen edges. Be careful when handling them.

Preparation

Tools:

Plus (+) screwdriver

Work table:

Prepare a table with a flat surface 105 cm x 65 cm or wider, and place a suitable cushion or soft cloth on it.

INSTALLATION

1

Turn off the power of the Plasma Display
Monitor and then disconnet the power
cord.

2

Remove the blank panel of the Plasma
Display Monitor.

1) Place the Plasma Display Monitor upside down

(with the screen faced downward) on the work
table gently.

Note:

Be careful not to get the screen glass scratched or
damaged.

2) Unscrew the 4 screws (

1

 to 

4

) indicated in the

illustration (Fig. 1) to detach the blank panel of
the Plasma Display Monitor.

Note:

This removed blank panel is not used when printed
board ass’y is installed. Retain all the screws for later
use.

3

Install the Video Input Unit.

1) There are two connectors on the inner surface of

the Video Input Unit.
By aligning these two connectors with the
connectors inside the monitor, push the Video
Input Unit so that the connectors are fully
connected.

2) Fix the Video Input Unit with the 4 screws

removed in step 2 (

1

 to 

4

) (Fig. 3).

4

Operate the Plasma Display Monitor.

After the Video Input Unit is installed, operate the
monitor and check that image and sound are
reproduced correctly through the following inputs:
VIDEO A, VIDEO B, and COMPONENT/RGB
terminals.

3

1

4

2

Fig. 3

Fig. 1

Fig. 2

Rear cover

Connector

Connector

Connector

Video Input Unit

Blank panel

3

1

4

2

Rear side

ENGLISH

RGB A

AUDIO

IN

REMOTE

RS-232C

WIRED

MAKE

VIDEO A

VIDEO

IN

OUT

AUDIO

L/MONO

R

VIDEO B

VIDEO

IN

Y/C IN

COMPONENT/RGB B

VIDEO

Y/G Pb/B

Pr/R

HD/Cs VD 

AUDIO

L/MONO

R

AUDIO

L/MONO

R

IF_C42P1G.p65

03.4.24, 2:51 PM

2

Summary of Contents for IF-C42P1G









Reviews: