Masterpage:Right-Full-NoTitle0
EN
71
Filename [HRS9850EU4.fm]
Page 71
May 21, 2001 1:37 pm
* The default setting is
bold
in the table below.
8
VIDEO STABILIZER
ON
OFF
When this function is set to “ON”, you can automatically correct vertical
vibration in the picture when playing back unstable recordings made on
another recorder.
NOTES:
●
When you finish viewing a tape, be sure to set this function to “OFF”.
●
Regardless of the setting, this function has no effect during recording and during special
effects playback.
●
The on-screen display may jitter vertically when this function is set to “ON”.
●
To watch recordings with close-caption, set this function to “OFF”.
●
Video Stabilizer and Digital TBC/NR cannot be used at the same time. If you activate
Digital TBC/NR when “VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be
automatically turned “OFF”.
8
S-VHS
ON
OFF
Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.
●
To record in S-VHS:
Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS
indicator lights up on the front display panel.
The S-VHS recording mode is selected.
●
To record in S-VHS ET on a VHS cassette:
See “Super VHS ET (S-VHS ET)” on page 27.
●
To record in VHS:
Insert a cassette marked “VHS”.
If the S-VHS ET indicator on the recorder’s front panel is lit and the S-VHS ET
mode is activated, press
S-VHS ET
. The S-VHS ET indicator goes off.
The VHS recording mode is automatically selected regardless of the “S-VHS”
mode setting.
●
To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front
display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off.
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS
indicator lights up on the front display panel regardless of the “S-VHS” mode setting.
8
COLOUR SYSTEM
PAL/NTSC
:
To record PAL
signals, or play
back a PAL or
NTSC tape.
MESECAM
:
To record
SECAM signals,
or play back a
MESECAM tape.
You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM*
signals on this recorder. Select the appropriate colour system.
* SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the
designation for tapes with SECAM signals that have been recorded on a
MESECAM-compatible PAL video cassette recorder.
NOTES:
●
It is not possible to record in S-VHS if “MESECAM” is selected. The recording mode is
forced to change to VHS.
●
If “MESECAM” is selected when the tape speed is set to EP mode, the tape speed will be
forced to change to LP mode.
●
It is not possible to select EP mode if “MESECAM” is selected.
About NTSC Playback
●
Some TVs shrink the picture vertically and place black bars at the top and bottom of the
TV screen. This is not a malfunction on the part of either the video recorder or the TV.
●
The picture may roll up and down. This can be corrected using the V-HOLD control
found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD
control.)
●
The counter and tape remaining time readings will be incorrect.
●
During search, still, or frame-by-frame playback, the picture will be distorted, and there
may be a loss of colour.
●
Depending on the type of TV, the top and bottom portions of superimposed displays
may be cut off during NTSC playback.
HRS9850EU1.book Page 71 Monday, May 21, 2001 1:44 PM
