JVC HR - S7950EU Instructions Manual Download

Page: 9 / 72

Masterpage:Right-NoTitle0

Filename [HRS7950EU1-EN.fm]

Page 9

March 6, 2002 1:49 pm

Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the

button.

(

墌

“Operating JVC TVs” below)

This remote control transmits A code signals only; it is not applicable to B code signals.

How To Use

The remote control can operate most of your video recorder’s functions, as well as basic functions of JVC TV sets. (

墌

“Operating

JVC TVs” below)

●

Point the remote control toward the receiving window.

●

The maximum operating distance of the remote control is about 8 m.

Operating JVC TVs

To operate your TV, while holding down the

button, press the corresponding button:

TV/VCR

TV PR

+/–

+/–

(TV Muting).

NOTES:

●

When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

●

Depending on the type of JVC TV, some or all functions may not be operated using the remote control.

●

If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

HRS7950EU1-EN.book Page 9 Wednesday, March 6, 2002 1:49 PM

Summary of Contents for HR - S7950EU









































































Search results

Summary of Contents for HR - S7950EU

Reviews:

Related manuals for HR - S7950EU

Brands by name

Popular brands

JVC HR - S7950EU, Instructions Manual

Search results

Summary of Contents for HR - S7950EU

Reviews:

Related manuals for HR - S7950EU

Brands by name

Popular brands