JVC HR-A51U, Instructions Manual

Page: 42 / 48

42
EN
REMOTE CONTROL
1 PROG. Button (
墌
pg. 28)
2 TV Button (See below)
3 DISPLAY Button (
墌
pg. 23)
4 TV/VCR Button (
墌
pg. 26)
5 Recording Speed [SP/EP] Button (
墌
pg. 17)
6 ENTER Button (
墌
pg. 17)
On-Screen Display [OSD] Button (
墌
pg. 24)
7 CANCEL Button (
墌
pg. 30)
Counter [C.] RESET Button (
墌
pg. 23)
8
START +/– Button (
墌
pg. 28)
9
STOP +/– Button (
墌
pg. 28)
0
Rewind [REW] Button (
墌
pg. 16)
!
PLAY Button (
墌
pg. 16)
@
Record [REC] Button (
墌
pg. 17)
#
MENU Button (
墌
pg. 10)
$
OK Button (
墌
pg. 10)
%
PROG. CHECK Button (
墌
pg. 30)
^
POWER On/Off Button (
墌
pg. 10)
&
NUMBER Buttons (
墌
pg. 17)
*
DAILY Timer Recording Button (
墌
pg. 29)
(
WEEKLY Timer Recording Button (
墌
pg. 29)
)
"AUX" Mode Select Button (
墌
pg. 35)
q
TIMER Button (
墌
pg. 29)
w
Channel [CH] +/– Button (
墌
pg. 17, 28)
e
DATE +/– Button (
墌
pg. 28)
r
Fast-Forward [FF] Button (
墌
pg. 16)
t
STOP Button (
墌
pg. 16)
y
PAUSE Button (
墌
pg. 18)
u
SHUTTLE PLUS
%fi
Button (
墌
pg. 10)
TV Channel [CH] +/– Button (See below)
i SHUTTLE PLUS
4 ¢
( ) Button (
墌
pg.
18, 19)
TV Volume [VOL] +/– Button (See below)
PROG.
CHECK
PROG.
TV operation – Press and hold
TV button, then press POWER,
TV CH +/–, VOL +/–, TV/VCR
POWER
TV
1 2 3
4 5
0
AUX
6
7 8
DAILY
9
WEEKLY
DISPLAY
TV/VCR
SP/EP
CANCEL
START
REW FF PLAY
REC
MENU
OK
STOP
TV CH +
TV CH –
TV
+ VOL
TV
VOL –
PAUSE
STOP DATE CH
C.RESET OSD
ENTER
TIMER
1
2
4
3
SHUTTLE PLUS SHUTTLE PLUS
*
t
3
4
5
7
6
8
0
!
@
#
$
%
y
r
1
2
9
^
&
w
e
(
)
q
u
i
LP20034-020
– +
INDEX (cont.)
% fi
Buttons with a small dot on the left side of the name can
also be used to operate your TV while holding down the
TV
button.
墌
“Operating JVC TVs” below.
This remote control transmits A code signals only; it is not
applicable to B code signals.
NOTES:
●
When inserting the batteries, be sure to insert in the
correct directions as indicated under the battery cover.
●
Depending on the type of JVC TV, there may be cases
where some or all functions cannot be operated using the
remote control.
●
If the remote control doesn't work properly, remove its
batteries. Replace with fully charged batteries and then
try again.
How To Use
The remote control can operate most of your VCR's
functions, as well as basic functions of JVC TV sets. (See
below.)
●
Point the remote control toward the sensor window.
●
The maximum operating distance of the remote
control is about 8 m.
Operating JVC TVs
To operate your TV, while holding down TV , press the
corresponding button: POWER, TV/VCR , TV CH+/– . TV
VOL +/– can be used without holding down TV .