1-15
3 –
: Mechanism Sensor Information
[Common table of MN and HD]
Display
Mechanism Sensor Information
S-VHS SW
REC SAFETY SW
START SENSOR
END SENSOR
0–
VHS
Tab broken
ON
ON
1–
VHS
Tab broken
ON
OFF
2–
VHS
Tab broken
OFF
ON
3–
VHS
Tab broken
OFF
OFF
4–
VHS
Tab present
ON
ON
5–
VHS
Tab present
ON
OFF
6–
VHS
Tab present
OFF
ON
7–
VHS
Tab present
OFF
OFF
8–
S-VHS
Tab broken
ON
ON
9–
S-VHS
Tab broken
ON
OFF
A–
S-VHS
Tab broken
OFF
ON
B–
S-VHS
Tab broken
OFF
OFF
C–
S-VHS
Tab present
ON
ON
D–
S-VHS
Tab present
ON
OFF
E–
S-VHS
Tab present
OFF
ON
F–
S-VHS
Tab present
OFF
OFF
*
6
: Cassette tape winding position
The cassette tape winding position at the moment of EMG is
displayed by dividing the entire tape (from the beginning to the
end) in 22 sections using a hex number from “00” to “15”.
“00” : End of winding
“15” : Beginning of winding
“FF” : Tape position not identified
– 4
: Mechanism Mode Position
[Table of MN]
Display
Mechanism Mode Position
-0
Initial value
-1
EJECT position
-2
Housing operating
-3
U/L STOP position
-4
Tape being loaded/unloaded (When the pole base is located on the front
side of the position just beside the drum)
-5
Tape being loaded/unloaded (When the pole base is located on the rear
side of the position just beside the drum)
-6
Pole base compressed position
-7
FF/REW position
-8
Between FF/REW and STOP with pinch roller compression ON
-9
STOP with pinch roller compression OFF
-A
Between STOP with pinch roller compression OFF and REV
-B
REV (REV STILL/SLOW) position
-C
Between REV and FWD
-D
FWD (FWD STILL/SLOW) position
-E
Between FWD and PLAY
-F
PLAY position
[Table of HD]
Display
Mechanism Mode Position
–0
EJECT position
–1
U/L STOP position
–2
Tape being loaded/unloaded (When the pole base is located on the rear
side of the position just beside the drum)
–3
FF/REW position
–4
STOP with pinch roller pressure off
–5
REV (REV STILL/SLOW) position
–6
FWD (FWD STILL/SLOW) position, PLAY position
–7
Intermediate position during transition between other mechanism modes
Note:
•
As the display is always “–7” at any intermediate position
between mechanism modes, the position of transitory
EMG may sometimes not be locatable.
Note:
•
The values of cassette tape type
2
in the above table are
typical values with representative cassette tapes.
*
7
: Cassette tape type
2
(Winding area)
Display
Cassette Tape Type
2
00
Cassette type not identified
07
Small reel, thick tape
T-5
08 - 0E
C cassette, thick tape
TC-10
09 - 15
C cassette, thick tape
TC-20P
0A - 0B
Small reel, thick tape
T-20
0A - 16
C cassette, thin tape
TC-30
0A - 16
C cassette, thin tape
TC-40
0D - 0F
Small reel, thick tape
T-40
11 - 14
Small reel, thick tape
T-60
15 - 18
Small reel, thick tape
T-80/DF-160
17 - 1A
Small reel, thick tape
T-80/DF-180
19 - 1D
Small reel, thick tape
T-100
1D - 21
Small reel, thick tape
T-120/DF-240
1E - 1F
Small reel, thin tape
T-140
1F - 23
Small reel, thick tape
T-130
21 - 23
Small reel, thin tape
T-160
21 - 23
Small reel, thin tape
T-168
22 - 24
Small reel, thick tape
DF-300
22 - 24
Small reel, thin tape
T-180/DF-380
22 - 24
Small reel, thin tape
T-210/DF-420
22 - 23
Large reel
T-5
23 - 24
Large reel
T-10
25 - 26
Large reel
T-20
27 - 29
Large reel
T-30
29 - 2B
Large reel
T-40
2D - 2F
Large reel
T-60
Notes:
•
Cassette tape type
1
is identified a few times during mode
transition and the identification count is variable depending on
the cassette tape type. If an EMG occurs in the middle of identi-
fication, the cassette tape type may not be able to be identified.
•
If other value than those listed in the above table is displayed,
the cassette tape type is not identified.
Display
Cassette Tape Type
1
00
Cassette type not identified
16
Large reel/small reel (T-0 to T-15/T-130 to T-210) not classified
82
Small reel, thick tape (T-120) identified/thin tape (T-140) identified
84
Large reel (T-0 to T-60) identified
92
Small reel, thick tape (T-130) identified/thin tape (T-160 to T-210) identified
93
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) not classified
C3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
D3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
E1
C cassette, thick tape (TC-10 to TC-20) identified
E2
Small reel, thick tape (T-0 to T-100) identified
E9
C cassette, thin tape (TC-30 to TC-40) identified
F1
C cassette, thick tape/thin tape (TC-10 to TC-40) not classified
*
5
: Cassette tape type
1
Note:
•
EMG detail information
2
is the reference information
stored using the remaining tape detection function of the
cassette tape. As a result, it may not identify cassette cor-
rectly when a special cassette tape is used or when the
tape has variable thickness.
1.11.5 Emergency detail information
2
The type of the cassette tape and the cassette tape winding po-
sition can be confirmed based on the figure in EMG detail infor-
mation 2 .
[FDP display]
*
5
:
*
6
:
*
7
*
5
: Type of the cassette tape in use 1
*
6
: Winding position of the cassette tape in use
*
7
: Type of the cassette tape in use 2 (Winding area)
