background image

1-2 (No.YF256<Rev.001>)

SPECIFICATION

„

Camcorder

„

AC Adapter

Design and specifications subject to change without notice.

For General

Power supply

DC 11 V (Using AC Adapter)
DC 7.2 V (Using battery pack)

Power consumption

Approx. 2.3 W* 
*When the LED light is off and the monitor backlight is set to [STANDARD] mode.

Dimensions (W 

×

 H 

×

 D)

54 mm 

×

 68 mm 

×

 111 mm(2-3/16" 

×

 2-11/16" 

×

 4-3/8")

Weight

Approx. 225 g (0.50 lbs) (incl. grip belt, cassette and lens cap)
Approx. 270 g (0.60 lbs) (incl. battery and grip belt)

Operating temperature

0

°

C to 40

°

C (32

°

F to 104

°

F)

Operating humidity

35% to 80%

Storage temperature

-20

°

C to 50

°

C (-4

°

F to 122

°

F)

Pickup

1/6" (680,000 pixels) CCD

Lens

F 1.8 to 4.0, f = 2.2 mm to 77.0 mm, 35:1 power zoom lens

Filter diameter

Ø30.5 mm

LCD monitor

2.7" diagonally measured, LCD panel/TFT active matrix system

Speaker

Monaural

LED Light

Within 1.5 m (4.9ft)(recommended shooting distance)

For video/Audio Format

SD-VIDEO

Recording/Playback 
format

Video

MPEG-2

Audio

Dolby Digital (2 ch)

Signal format

NTSC standard                   

Recording mode (video) ULTRA FINE

720 x 480 pixels, 8.5 Mbps(VBR)

FINE

720 x 480 pixels, 5.5 Mbps (VBR)

NORMAL

720 x 480 pixels, 4.2 Mbps (VBR)

ECONOMY

352 x 240 pixels, 1.5 Mbps (VBR)

Recording mode (audio) ULTRA FINE

48 kHz, 384 kbps

FINE

48 kHz, 384 kbps

NORMAL

48 kHz, 256 kbps

ECONOMY

48 kHz, 128 kbps

For still image

Format

JPEG

Image size

640 

×

 480

Picture quality

2 modes (FINE/STANDARD)

For connectors AV output

Video output

1.0 V (p-p), 75 

Audio output

300 mV (rms), 1 k

USB

Mini USB type A and B, USB 2.0 compliant

Power requirement

AC 110 V to 240 V, 50 Hz/60 Hz

Output

DC 11 V, 1 A

Summary of Contents for GZ-MS100UC






















Reviews: