JVC GY-HM100, Instructions Manual

Page: 40 / 76

40
Shooting
Applica b le to: Video shooting mode
There are three ways to input audio sound.
A
Built-in microphone
B
MIC terminal
C
INPUT1 terminal / INPUT2 terminal
The priority order of the input is in the se q uence of
C
>
B
>
A
.
T When the b uilt-in microphone or MIC terminal is in use,
remove the audio unit ca b le from the AUDIO IN terminal.
Memo :
●
Audio sound is not recorded when in the still picture
shooting mode.
Setting the Reference Audio Recording
Level
Applica b le to: Full Auto shooting mode
A
, Manual shooting
mode
M
Menu settings
S et the [AUDIO REF. LEVEL] menu.
(-20 dB/-12 dB) ( A Page 64)
U s ing the Built-in Microphone
Applica b le to: Full Auto shooting mode
A
, Manual shooting
mode
M
䡵
S etting the input level.
Menu settings
S et the [INTERNAL MIC LEVEL] menu.
( A Page 64)
U s ing an External Microphone Connected
to the MIC Terminal
Applica b le to: Full Auto shooting mode
A
, Manual shooting
mode
M
Preparation: Connect a microphone to the MIC terminal.
(
A
Page 18)
䡵
S etting the input level.
Menu settings
S et the [MIC LEVEL S ETTING] menu. (
A
Page 64)
U s ing an External Microphone Connected
to the INPUT1/INPUT2 Terminal
Applica b le to: Full Auto shooting mode
A
, Manual shooting
mode
M
Preparation: Connect a microphone to the INPUT1/INPUT2
terminal. (
A Page 18)
䡵
Selecting CH-2 audio
Configure the CH-2 INPUT switch
INPUT1: Inputs the audio from the INPUT1 terminal to CH-2.
INPUT2: Inputs the audio from the INPUT2 terminal to CH-2.
Memo :
●
The audio from the INPUT1 terminal is input to CH-1
regardless of the setting.
䡵
Selecting the audio input to the INPUT1 or
INPUT2 terminal
Caution :
●
When connecting a device that does not re q uire a +48 V
power supply, make sure that it is not set to the MIC+48V
position.
䡵
Adju s ting the audio recording level
S elect a method for adjusting the audio recording level.
Configure the CH-1/CH-2 audio select switch.
S elect whether to set each channel to the AUTO or
MANUAL mode.
Reducing Wind Noi s e
Wind noise for each microphone can b e reduced.
Menu settings
S et the [WIND CUT] menu. (
A
Page 6 3 )
Audio Recording
MIC
B
MIC Terminal
A
Built-in Microphone
C
INPUT1/INPUT2 Terminals
Audio Unit Ca b le
Terminal Audio Input
INPUT1 Input to CH-1(L) at all times. Input to CH-2(R) can
b e ena b led using the CH-2 INPUT switch.
INPUT2 Input to CH-2(R) can b e ena b led using the CH-2
INPUT switch.
Configure the INPUT1/INPUT2 AUDIO INPUT switch.
LINE : Use this setting when connecting to an
audio device or other e q uipment.
MIC : Use this setting when connecting to a
dynamic microphone.
MIC+48V : Use this setting when connecting to a
microphone that re q uires a +48 V power
supply (phantom microphone), or when
using the supplied microphone.
AUTO : Use this setting to ena b le the auto
adjustment mode.
MANUAL : Use this setting to ena b le the manual
adjustment mode. Adjust the audio
recording level using the CH-1/CH-2
AUDIO LEVEL kno
b .
CH-1/CH-2 Audio S election S witch
INPUT1/INPUT2 AUDIO INPUT S witch
CH-2 INPUT
S witch
CH-1/CH-2 AUDIO LEVEL Kno b
M9H7_EN_001D.book Page 40 Thursday, August 26, 2010 11:51 AM