JVC GR-D63, Instructions Manual

Page: 38 / 56

EDITING
38
EN
MasterPage: Left
The audio track can be customised only when recorded
in the 12-bit and SP modes. (
墌
pg. 25)
●
Use the provided remote control.
1
Play back the tape to locate the point where editing
will start, then press PAUSE (
9
).
2
While holding A. DUB (
D
) on the remote control,
press PAUSE (
9
). The “
9
D
” and “MIC” indicators
appear.
3
Press PLAY (
U
), then begin “narrating”. Speak into
the microphone.
●
To pause dubbing, press PAUSE (
9
).
4
To end Audio Dubbing, press PAUSE (
9
), then STOP
(
8
).
To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”. (
墌
pg. 24, 28)
NOTES:
●
Sound is not heard from the speaker during Audio Dubbing.
●
When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
●
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
●
If feedback or howling occurs during TV playback, move the
camcorder’s microphone away from the TV, or turn down
the TV’s volume.
●
If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective from
the point where 16-bit recording began.
●
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops.
●
To perform Audio Dubbing while watching on the television,
make connections. (
墌
pg. 17)
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
●
Use the provided remote control.
NOTES:
●
Before performing the following steps, make sure that
“TIME CODE” is set to “ON”. (
墌
pg. 24, 28)
●
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
●
To perform Insert Editing while watching in the television,
make connections. (
墌
pg. 17)
1
Play back the tape, locate the Edit-Out point and
press PAUSE (
9
). Confirm the time code at this point.
(
墌
pg. 13)
2
Press REW (
3
) until the Edit-In point is located,
then press PAUSE (
9
).
3
Press and hold INSERT (
I
) on the remote control,
then press PAUSE (
9
). The “
9
I
” indicator and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
4
Press START/STOP to begin editing.
●
Confirm the insert at the time code you checked in step
1
.
●
To pause editing, press START/STOP . Press it again to
resume editing.
5
To end Insert Editing, press START/STOP , then
STOP (
8
).
NOTES:
●
Program AE with special effects (
墌
pg. 30) can be used to
spice up the scenes being edited during Insert Editing.
●
During Insert Editing, the date and time information
changes.
●
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure you
only edit recorded areas.
●
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops. (
墌
pg. 43)
Audio Dubbing
T
W
PAUSE
PLAY
A.DUB
STOP
REW
INSERT
START/
STOP
Speaker
Stereo Microphone
Insert Editing
GR-D63EK_07Advanced.fm Page 38 Wednesday, December 17, 2003 1:10 PM