background image

G-1

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an appro-
priate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved
type, as originally fitted.

If nontheless the mains plug is cut off ensure to remove the fuse
and dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow
the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.

The wires in the mains lead on this product are coloured in
accordance with the following code:

Blue :Neutral

Brown :Live

As these colours may not correspond with the coloured mark-
ings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the termi-
nal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the ter-
minal which is marked with the letter L or coloured red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Caution — 

 switch!

Disconnect the mains plug to shut the power off completely.
The 

 switch in any position does not disconnect the mains

line. The power can be remote controlled.

Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage,
locate the apparatus as follows:
1

Front: No obstructions and open spacing.

2

Sides/ Top/ Back:No obstructions should be placed in the
areas shown by the dimensions below.

3

Bottom:Place on the level surface. Maintain an adequate
air path for ventilation by placing on a stand with a height of
10 cm or more.

CAUTION
To reduce the risk of electrical shocks, fire, etc.:

1

Do not remove screws, covers or cabinet.

2

Do not expose this appliance to rain or moisture.

IMPORTANT FOR LASER PRODUCTS

REPRODUCTION OF LABELS
1

CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE

2

WARNING LABEL, PLACED INSIDE THE UNIT

1

CLASS 1 LASER PRODUCT

2

DANGER: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.

3

CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to qual-
ified service personnel.

SAFETY PRECAUTIONS
Prevention of Electric Shocks, Fire Hazards and Damage
1

Even when the 

%

 

button is set to STANDBY, a very small

current will flow. To save power and for safety when not
using the unit for an extended period of time, disconnect
the power cord from the household AC outlet.

2

Do not handle the power cord with wet hands.

3

When unplugging from the wall outlet, always grasp and
pull the plug, not the power cord. 

4

Consult your nearest dealer when damage, disconnection,
or contact failure affects the cord.

5

Do not bend the cord severely, or pull or twist it.

6

Do not modify the power cord in any manner.

7

To avoid accidents, do not remove screws to disassemble
the unit and do not touch anything inside the unit.

8

Do not insert any metallic objects into the unit.

9

Unplug the power cord when there is a possibility of lightning.

10 Do not use this apparatus in a bathroom or places with water. 

Also do not place any containers filled with water or liquids
(such as cosmetics or medicines, flower vases, potted plants,
cups, etc.) on top of this apparatus.

11 Do not block the ventilation opcnings or holes. (If the venti-

lation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)

12 Do not place any naked flame sources, such as lighted

candles, on the apparatus.

13 When discarding batteries, environmental problems must

be considered and local rules or laws governing the dis-
posal of these batteries must be followed strictly.

CLASS    1

LASER     PRODUCT

CAUTION 

About the Internal Cooling Fan

This unit includes an internal cooling fan, so as to allow for high-power operation within a small space. 
This fan comes on when the sound level is set high, and may also come on even at low sound levels if the internal temperature rises. To
ensure effective fan operation, please leave at least 15cm clearance between the rear of the unit and the wall, and at least 1cm clearance
on each side of the unit. 

10 cm

15 cm

15 cm

15 cm

1 cm

1 cm

STANDBY/ON

OPEN/CLOSE

PHONES

15 cm

15 cm

Front view

Side view

FS-SD550(B)_Warning.fm  Page 1  Monday, January 15, 2001  9:12 AM

Summary of Contents for FS-SD550A





























Reviews: