Masterpage:Right0
EN
17
Filename [M100SEK_05Name.fm]
INSTALLING YOUR NEW UNIT
It’s essential that your unit be properly connected.
1
Place the unit on a stable, horizontal surface.
2
Connect the unit to a TV depending on the TV and cables you
use.
8
Basic Connection
To connect to a TV with 21-pin SCART input connector
^
A
Disconnect the TV aerial cable from the TV.
B
Connect the TV aerial cable to the [ANTENNA IN] connector on
the rear panel of the unit.
C
Connect the [ANTENNA OUT] connector on the rear panel of
the unit and the TV’s aerial connector with the supplied RF
cable.
D
Connect the [L-1 IN/OUT] connector on the rear panel of the
unit and the TV’s 21-pin SCART connector with a supplied 21-
pin SCART cable.
●
The [L-1 IN/OUT] connector accepts and delivers either a
composite signal (regular video signal), Y/C signal or RGB
signal.
●
Set your TV to the VIDEO, Y/C, or RGB mode according to the
type of your TV’s SCART connector.
8
Component Video Connection
To connect to TV’s component video input connectors
^
A
Perform steps
A
-
C
of
A
Basic Connection
B
.
B
Connect the unit’s [COMPONENT VIDEO OUT (Y/P
B
/P
R
)]
connectors to the TV’s component video input connectors.
C
Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
input connectors.
●
You can obtain high-quality component video pictures.
●
If your TV is not stereo-capable, use the unit’s [AUDIO OUT]
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
●
By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to
A
Scan Mode Set
B
(
A
pg. 64).
NOTE:
Select an appropriate option of
A
L-1 OUTPUT
B
as follows
(
A
pg. 58):
When the setting selected is not in accordance with the TV
connected and depending on the type of appliance connected to
the unit, the correct picture will not appear.
3
Plug the end of the mains power cord into a mains outlet.
●
A
PLEASE
B
and
A
WAIT
B
blink alternately on the front display
panel when the AC plug of the mains power cord is connected
into a mains outlet. And it takes approximately 30 seconds for
the unit to be turned on. This is not a malfunction.
Basic Connection
ATTENTION:
●
Your TV must have a 21-pin AV input connector (SCART) for
the basic connection to the unit.
●
Connect the AC plug only after all connections to the TV has
been completed.
COAXIAL
Y
P
B
P
R
IN
OUT
ANTENNA
VIDEO OUT
L-1
L-2
TV aerial cable
Mains outlet
Back of unit
Component
video cable
(not supplied)
TV
Mains power cord
Audio cable
(not supplied)
To
[COMPONENT
VIDEO OUT
(Y/P
B
/P
R
)]
To
[AUDIO
OUT]
To [ANTENNA IN]
To
[ANTENNA
OUT]
RF cable
(supplied)
To [L-1 IN/OUT]
21-pin SCART
cable
(supplied)
To 75 ohm terminal
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
When your TV’s SCART
connector accepts:
Set
A
L-1 OUTPUT
B
to:
Composite signals
A
SCART VIDEO
B
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
A
SCART S-VIDEO
B
RGB signal
A
SCART RGB
B
Component video signal
A
COMPONENT
B
If you possess a satellite receiver, refer to
A
Connecting To A
Satellite Receiver
B
as well. (
A
pg. 60)
M100SEK_00.book Page 17 Tuesday, March 22, 2005 5:31 PM
