JVC DR-DX5SE, Instructions Manual

Page: 48 / 92

Filename [DX5SEU_10Timer Recording.fm]
Masterpage:Left+
48
EN
TIMER RECORDING ON HDD/DVD DECK
Page 48Wednesday, 23 November 2005 14:13
This function allows you to automatically record a satellite
programme which is timer programmed on your external satellite
receiver. Connect a satellite receiver to the unit’s [L-2 IN/DECODER]
connector and programme the timer on the satellite receiver. The unit
starts or stops recording by the signals input from the satellite
receiver. After recording, the unit’s power shuts off automatically.
1
Press HDD on the remote control to choose the recording deck.
You can also press DV/HDD/DVD SELECT on the unit
repeatedly to select the recording deck.
2
Set A L-2 SELECT B to A SAT VIDEO B or A SAT S-VIDEO B .
(
A
pg. 63)
●
Also refer to A
IMPORTANT
B on page 69.
3
Press REC MODE repeatedly to set the recording mode.
4
Press and hold SAT
j
for about 2 seconds to engage the
Automatic Satellite Programme Recording mode. A
V
B and
A SAT
j
B appear on the front display panel.
NOTES:
●
To disengage the Automatic Satellite Programme Recording
mode, press
SAT
j
.
●
If the unit’s power is off, it is not possible to engage the Automatic
Satellite Programme Recording mode.
●
In step 4 , if A
V
B blinks quickly on the front display panel even
though your satellite receiver’s power is off, Automatic Satellite
Programme Recording will not work properly with that satellite
receiver*. If this is the case, perform
A Manual Timer
Programming B (
A
pg. 46) to timer record a satellite programme.
* Some satellite receivers output signals even if the power is off. Automatic
Satellite Programme Recording is not possible with those satellite
receivers.
●
A
V
B blinks on the front display panel while Automatic Satellite
Programme Recording is in progress.
●
For timer programming of the satellite receiver, refer to the
instruction manual of the satellite receiver.
●
Automatic Satellite Programme Recording is not possible if your
satellite receiver does not have a timer.
●
If there are more than one satellite programmes you wish to
record with Automatic Satellite Programme Recording, it is not
possible to set different recording modes for each programme.
●
Depending on the type of satellite receiver, the unit may not
record a slight portion of the beginning of the programme or may
record slightly longer than the actual length of the programme.
●
If you engage the Automatic Satellite Programme Recording
mode when the satellite receiver’s power is on, the unit will not
start Automatic Satellite Programme Recording even though
A
V
B
blinks on the front display panel. When the satellite receiver shuts
off once and is turned back on again, the unit starts recording.
●
You can also record a programme from your cable system in the
same way if the system has a timer.
●
Just Clock (
A
pg. 77) does not work when the Automatic Satellite
Programme Recording mode is engaged.
Automatic Satellite Programme
Recording
(HDD Deck Only)
ATTENTION:
●
Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the unit will start recording
when the satellite receiver’s power is turned on.
●
If you have connected another appliance other than a satellite
receiver to the [L-2 IN/DECODER] connector, be sure not to
engage the Automatic Satellite Programme Recording mode;
otherwise, the unit will start recording when the connected
appliance’s power is turned on.
●
Automatic Satellite Programme Recording and timer recording
cannot be done at the same time.
REC MODE
DV/HDD/DVD
SELECT
SAT j
REC MODE
HDD
CABLE/SAT
DVD TV
●
Make sure the satellite receiver is connected to the unit’s [L-2
IN/DECODER] connector.
●
Programme the timer on the satellite receiver.
●
Slide the TV/CABLE/SAT/DVD switch to DVD .
DX5SEU_00.book Page 48 Wednesday, November 23, 2005 2:13 PM