JVC DPT 115 Operation Manual Download Page 5

Page: 5 / 37

PAN & TILT HEAD SPECIFICATIONS:

HARACTERISTICS

Operating

Environment ................................................Indoor

Temperature.................................................................40 to 104 degrees F. (0 to 40 degrees C.)

Pan

Rotation ................................................................260 degrees with adjustable limit switches

Tilt

Angle ......................................................................+/- 45 degrees with adjustable limit switches

Pan

Speed ...................................................................Continuously variable to 15 degrees/second

Tilt

Speed .....................................................................Continuously variable to 7.5 degrees/second

Load

Mounting..............................................................Side loading with alignment of image plane

and center of rotation

Capacity .......................................................................8 pounds

ILT

ONTROL

Pan/Tilt .........................................................................0 to +12 VDC (DC coreless motor)

Presets .........................................................................Yes

Max. distance between controller & p/t head................2,000 feet (Contact ESI for longer distances)

Interface to Controller...................................................RS-422 differential over 4 wire cable

..................................................RS-232 Interface for Controller/computer

control and dual controllers

Special

Functions .........................................................Externally accessible DIP switches

ENS

ONTROL

Focus ...........................................................................Teleconferencing and CCTV lenses

Zoom ............................................................................Teleconferencing and CCTV lenses

Iris

(Optional)................................................................Teleconferencing and CCTV lenses

Multi-Lens

Control ........................................................Different lens configurations selected from

Internal Jumper settings

Lens Interface Cable ....................................................Available (see Interface Cable Design Guide)

Presets .........................................................................Zoom & focus

HYSICAL

HARACTERISTICS

Size (surface mount) ...................................................4.5 (W) X 7.5 (H) X 3.5 (D) inches

Weight ..........................................................................5 Pounds

Mounting ......................................................................4 mounting holes (1 15/16 x 4 15/16)

OWER

NPUT

EQUIREMENTS

Voltage .........................................................................+15 VDC unregulated

Current .........................................................................0.8 Amperes

Power ON Switch .........................................................Yes, located on Pan & Tilt base

Power ON Indicator ......................................................Yes, located on Pan & Tilt base

Power

Adapter..............................................................Supplied with Pan & Tilt head

Power

Input ..................................................................From either supplied power adapter

or other appropriate DC power source

2/12/05

Document D0153

Summary of Contents for DPT 115






































Search results

Summary of Contents for DPT 115

Reviews:

Related manuals for DPT 115

Brands by name

Popular brands

JVC DPT 115, Operation Manual

Search results

Summary of Contents for DPT 115

Reviews:

Related manuals for DPT 115

Brands by name

Popular brands