JVC DPT 115 Operation Manual Download Page 12 | Manualshive

Page: 12 / 37

background image

4.2 INDICATORS

4.2.1 Power Indicator-Green LED

The Power LED is located adjacent to the power switch on the pan and tilt switch panel. When
the “POWER” LED is illuminated, the power switch is closed and power is applied to the pan
and tilt head control electronics.

4.2.2 Data Indicator-Red LED

The red Data LED is located adjacent to the power switch on top of the power LED on the pan
and tilt switch panel. When the “DATA” LED is illuminated, data is being sent to pan and tilt, or
pan/tilt is in the process of going to a preset.

2/12/05

Document D0153

12

«
...
10
11
12
13
14
...
»

Summary of Contents for DPT 115






































Reviews:

No comments

Related manuals for DPT 115

DS1-MP10RX series

Brand: NEC Pages: 39

AUTOSTROKE AST-200-V2

Brand: StoneAge Pages: 28

Brand: RayTek Pages: 2

Brand: Ace Bayou Pages: 8

Brand: B-TEK Scales Pages: 3

Brand: B-Speech Pages: 18

Brand: B-PWR Pages: 12

BIM-BAM GNS-921

Brand: e2 elektro Pages: 2

Brand: ICC Pages: 32

Brand: Hama Pages: 60

Brand: BAFANG Pages: 4

Brand: Idis Pages: 20

Brand: IHP Pages: 2

Brand: Nautronic Pages: 7

Brand: NAPCO Pages: 16

Brand: Harol Pages: 17

Brand: Cab Technology Pages: 10

Brand: Waldbeck Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands