5
ENGLISH
Rear panel
4
3
RGB OUT1
R
G
B
Hs/Cs
Vs
RGB OUT2
COMMERCIAL
USE ONLY
PC IN
VIDEO OUT
SYNC.
REMOTE IN (RS-232C)
MODE
0
1
A B C D
1
2
AC OUTLET
AC100-120V 50/60Hz
AC100-
120V
50/60Hz
40W
(UNSWITCHED
MAX400W)
DC OUT 12V
400mA
1 2
3
4
5
6
7
9
8
!
0
1
MODE switch
: Sets the type of signal output to the RGB output connector from the camera. Set this switch according to the
specifications of the connected projector and display. When you want to change the mode, turn the unit off
and then turn it on again.
* Mode 1 picture quality is high-
est. Mode 4 is lowest.
* When the mode is set to 2, 3
or 4, resolution will be re-
duced and picture quality may
be degraded.
2
SYNC. switch
: Use to set the mode for the sync signal output to the RGB output connectors or turn the on-screen display on/off.
Set this switch according to the specifications of the connected projector and display.
When you want to change the mode, turn the unit off and then turn it on again.
Mode
Connected projector/display
Output signal
1
SXGA (1280 x 1024)
1280 x 960 equivalent
2
XGA (1024 x 768)
1024 x 768 equivalent
3
SVGA (800 x 600)
800 x 600 equivalent
4
VGA (640 x 480)
640 x 480 equivalent
A
B
C
D
Horizontal sync signals
are output.
1
Sync signals are not
added to G signals.
On-screen signals are
output.
Unused
Composite sync sig-
nals are output.
0
Sync signals are added
to G signals.
On-screen signals are
not output.
Unused
A
: Sets the type of sync signals output to the RGB OUT1 Hs/Cs connector and RGB OUT2 connector.
B
: Sets whether or not sync signals are added to the video signal output at the RGB OUT1 G connector
and RGB OUT2 connector.
C
: Sets whether or not the on-screen display signal is output to the video signal output at the RGB OUT1
and 2 connectors.
* On-screen signals are output to the VIDEO OUT connector regardless of the mode setting.
The default setting at the factory is: A = 1, B = 1, C = 1 and D = 1.
3
REMOTE IN connector : Connect a personal computer to this connector for remote PC operation (p. 18).
4
RGB OUT1 connectors : Output signals from the camera or PC IN connector and the sync signal (BNC connectors).
5
RGB OUT2 connector : Outputs signals from the camera or PC IN connector and the sync signal (D-sub 15 pins).
* The RGB OUT1 and OUT2 connectors output the same picture and sync signal at the same time.
6
PC IN connector
: Input the RGB signal and sync signal from another device here. Signals can be output to the RGB OUT connectors.
Set the sync signal for the equipment connected to the PC IN connector according to the specifications
of the projector and display.
When connecting a personal computer, set its resolution to a suitable level.
7
VIDEO OUT connector : Outputs the video composite signal from the camera.
Use the VIDEO OUT button to switch between video output and RGB output.
Note :
When video signals from the camera are output to the VIDEO OUT connector, no signal is output to
the RGB OUT connectors.
8
AC IN connector
: Connect the power cord here.
9
AC outlet
: Supplies power of up to 400 W regardless of the power switch setting.
0
DC OUT connector
: Use this connector to supply DC power to the optional LCD monitor (TA-AV-Z7U).
!
LCD monitor holder
: Use to mount the optional LCD monitor (TA-AV-Z7U). For installation, refer to the LCD monitor’s operating
instructions.
