JVC AV-14F13 Service Manual Download Page 16

Page: 16 / 61

No.52021

AV-14F13

AV-14F33

BASIC OPERATION IN SERVICE MENU

1. TOOL OF SERVICE MENU OPERATION

Operate the SERVICE MENU with the REMOTE CONTROL UNIT.

2. SERVICE MENU ITEMS

In general basic setting (adjustments) items or verifications are performed in the SERVICE MENU.

(1) PICTURE

･･･････････････････

This set the setting values (adjustment values) of the VIDEO/CHROMA and DEFLECTION circuits.

(2) SOUND

[ AV-14F33/PH ]

･････

This set the setting values (adjustment values) of the AUDIO circuit.

(3) VIDEO STATUS

･････････････

This is used when the THEATER and GAME MODE is adjusted.

(4) OTHERS

･･･････････････････

This is used when the OTHERS MODE is adjusted.

(5) LOW LIGHT

･････････････････

This sets the setting values (adjustment values) of the WHITE BALANCE circuit.

(6) HIGH LIGHT

････････････････

This sets the setting values (adjustment values) of the WHITE BALANCE circuit.

(7) RF AFC CHK

････････････････

This is used when the RF AFC CHK MODE is verified.

[Do not adjust]

(8) VCO (CW)

･･････････････････

This is used when the IF VCO is adjusted.

(9) I

C BUS CTRL

･･･････････････

This is used when ON/OFF of the I

C BUS CTRL is set.

[Fixed ON]

(10)

SETUP TOUR OFF

･･････････

It should be able to select mode (LANGUAGE and SET CLOCK).

[Should be OFF]

3. Basic Operations of the SERVICE MENU

(1) How to enter the SERVICE MENU.

Press the DISPLAY key and VIDEO STATUS key of the remote control unit
at the same time to enter the SERVICE MENU screen

①

shown in figure page later.

(2) SERVICE MENU screen selection

Press the UP / DOWN key of the MENU to select any of the
following items.
(The letters of the selected items are displayed in yellow.)

(3) Enter the any setting ( adjustment ) mode

PICTURE, SOUND and OTHERS mode

1) If select any of PICTURE, SOUND or OTHERS items, and the LEFT / RIGHT key is pressed from SERVICE MENU ( MAIN

MENU ), the screen

②

will be displayed as shown in figure page later.

2) Then the UP / DOWN key is pressed, the PICTURE mode screen

③

or the SOUND mode screen

④

or the OTHERS mode

screen

⑤

is displayed, and the PICTURE, SOUND or OTHERS setting can be performed.

VIDEO STATUS, LOW LIGHT, HIGH LIGHT, RF AFC CHK, VCO (CW) and I

C BUS CTRL mode

1) If select any of VIDEO STATUS / LOW LIGHT / HIGH LIGHT / RF AFC CHK / VCO (CW) / I

C BUS CTRL items, and the LEFT

/ RIGHT key is pressed from SERVICE MENU ( MAIN MENU ), the screens

⑥

⑦

⑧

⑨

⑩

⑪

will be displayed as shown in

figure page later.

2) Then the settings or verifications can be performed.

SETUP TOUR OFF mode

1) If select of SETUP TOUR OFF item from SERVICE MENU , and you can change the ON or OFF(

should be OFF

(Should be OFF)

If it is ON, then you turn the TV power off, when you are turn the TV power on again.

The JVC is logo will be shown about 15 seconds automatically.

2) MENU

-/+

Key

･････････････

Select Language.

3) MENU

▼

Key

･････････････

Auto Search.

SERVICE MENU

SELECT BY
OPERATE BY

EXIT BY

PICTURE

SOUND

VIDEO STATUS

OTHERS

LOW LIGHT

HIGH LIGHT

RF AFC CHK
VCO (CW)

I2C BUS CTRL

SETUP TOUR(OFF)

EXIT

[AV-14F33/PH Only]

Summary of Contents for AV-14F13






























































Search results

Summary of Contents for AV-14F13

Reviews:

Related manuals for AV-14F13

Brands by name

Popular brands

JVC AV-14F13, Service Manual

Search results

Summary of Contents for AV-14F13

Reviews:

Related manuals for AV-14F13

Brands by name

Popular brands