JVC AV-14F13 Service Manual Download Page 10

Page: 10 / 61

No.52021

AV-14F13

AV-14F33

MEMORY IC REPLACEMENT

1. Memory IC

This model uses a memory IC.
The memory IC stores data for proper operation of video and deflection circuits.
When replacing, be sure to use an IC containing this (initial value) data.

2. Memory IC replacement procedure

(1)

Power off

Switch off the power and disconnect the power cord from the wall
outlet.

(2)

Replace the memory IC

Be sure to use memory ICs written with the initial data values.

(3)

Power on

Connect the power cord to the wall outlet and switch on the
power.

(4)

System constant check and setting

1) Simultaneously press the DISPLAY key and VIDEO STATUS

key of the remote control unit.

2) The SERVICE MENU screen of Fig.1 is displayed.
3) While the SERVICE MENU is displayed, again simultaneously

press the DISPLAY and VIDEO STATUS keys to display the
Fig.2 SYSTEM CONSTANT screen.

4) Refer to the SYSTEM CONSTANT table and check the setting

items. Where these differ, select the setting item with the
MENU UP / DOWN key and adjust the setting value with the
MENU LEFT / RIGHT keys.

5) After adjusting, release the MENU LEFT / RIGHT key to store

the setting value.

6) Press the EXIT key twice to return the normal screen.

This illustration is written about RM-C373GY(AV-14F33/PH),

There are no key of HYPER SURROUND in the RM-C372GY

(AV-14F13/PH).

(5)

Receive channel setting

Refer to the OPERATING INSTRUCTIONS (USER

’

S GUIDE)

and set the receive channels (Channels Preset) as described.

(6)

User settings

Check the user setting items according to Table 2.
Where these do not agree, refer to the OPERATING
INSTRUCTIONS (USER

’

S GUIDE) and set the items as

described.

(7)

SERVICE MENU setting

Verify what to set in the SERVICE MENU, and set whatever is
necessary. (Fig.1) Refer to the SERVICE ADJUSTMENT for
setting.

SERVICE MENU

SELECT BY
OPERATE BY

EXIT BY

PICTURE

SOUND

VIDEO STATUS

OTHERS

LOW LIGHT

HIGH LIGHT

RF AFC CHK
VCO (CW)

I2C BUS CTRL

SETUP TOUR(OFF)

EXIT

Fig.1

[ AV-14F33/PH Only ]

SYSTEM CONSTANT

SELECT BY
OPERATE BY

EXIT BY

VIDEO

AUDIO

VARI. OUT

GAME

YES

CINEMA

YES

EXIT

SYSTEM CONSTANT

SELECT BY
OPERATE BY

EXIT BY

CCD

YES

SURROUND

M37272M8-

×××

EXIT

***

Fig.2

DISPLAY

Key

VIDEO STATUS

Key

EXIT

Key

NAME OF REMOTE CONTROL KEYS

MENU
(UP) Key

MENU

＋

(RIGHT) Key

MENU
(DOWN) Key

POWER Key

NUMBER Key

MENU

－

(LEFT) Key

Summary of Contents for AV-14F13






























































Search results

Summary of Contents for AV-14F13

Reviews:

Related manuals for AV-14F13

Brands by name

Popular brands

JVC AV-14F13, Service Manual

Search results

Summary of Contents for AV-14F13

Reviews:

Related manuals for AV-14F13

Brands by name

Popular brands