EN
40
USING THE REMOTE CONTROL UNIT
Audio Dubbing
The audio track can be customized only when recorded
in the 12-bit mode (
墌
pg. 32).
NOTES:
●
Audio Dubbing is not possible on a tape recorded in
16-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
●
To perform Audio Dubbing while watching on the
television, make connections (
墌
pg. 16).
1
Play back the tape to locate the point where editing
will start, then press
PAUSE
(
6
)
H
.
2
While holding
A.DUB
(
e
)
S
on the remote control,
press
PAUSE
(
6
)
H
. “
6e
”
O
and “MIC” appear.
3
Press
PLAY
(
4
)
D
, then begin “narrating”.
Speak into the microphone.
• To pause dubbing, press
PAUSE
(
6
)
H
.
4
To end Audio Dubbing, press
PAUSE
(
6
)
H
, then
STOP
(
5
)
G
.
To hear the dubbed sound during playback . . .
..... set “12bit MODE” to “SOUND 2” or “MIX” in the
Menu Screen (
墌
pg. 36).
NOTES:
●
Sound is not heard from the speaker during Audio
Dubbing.
●
When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
●
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
●
If feedback or howling occurs during TV playback, move
the camcorder’s microphone away from the TV, or turn
down the TV’s volume.
●
If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.
●
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops (
墌
pg. 56).
●
To perform Audio Dubbing with a video unit connected to
the camcorder’s S/AV connector
&
, first set “S/AV
INPUT” to “A/V IN” or “S IN” in the Menu Screen
(
墌
pg. 35). “AUX” appears instead of “MIC”.
Insert Editing
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
NOTES:
●
Before performing the following steps, make sure that
“TIME CODE” is set to “ON” in the Menu Screen
(
墌
pg. 35, 36).
●
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
●
To perform Insert Editing while watching in the television,
make connections (
墌
pg. 16).
1
Play back the tape, locate the Edit-Out point and
press
PAUSE
(
6
)
H
. Confirm the time code at this
point (
墌
pg. 35, 36).
2
Press
REW
(
2
)
a
until the Edit-In point is located,
then press
PAUSE
(
6
)
H
.
3
Press and hold
INSERT
(
w
)
A
on the remote
control, then press
PAUSE
(
6
)
H
. “
6w
”
0
and the
Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.
4
Press
START/STOP
k
to begin editing.
• Confirm the insert at the time code you checked in
step
1
.
• To pause editing, press
START/STOP
k
. Press it
again to resume editing.
5
To end Insert Editing, press
START/STOP
k
, then
STOP
(
5
)
7
.
NOTES:
●
Programme AE with special effects (
墌
pg. 27) can be
used to spice up the scenes being edited during Insert
Editing.
●
During Insert Editing, the date and time information
changes.
●
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
●
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops (
墌
pg. 56).
●
If a memory card is loaded and “NAVIGATION” is set to
“ON”, a NAVIGATION thumbnail image is stored in the
memory card (
墌
pg. 21).
Stereo
microphone
R
j
I
s
g
f
U
P
a
O
d
k
l
;
A
S
D
F
G
H
h
K
J
Y
T
