background image

7

www.juwent.com.pl

Notify the forwarding company immediately in case of any transport damages.

Missing  parts  and  transport  damages  can  only  be  claimed  from  the  transport  insurance,  if  the 

damage is acknowledged by the forwarding company.

6.  SAFETY RECOMMENDATIONS

 

Use the electric unit in compliance with this User Manual.

Commissioning, installation, connection, inspections and repairs shall be carried out by 

an authorised electrician.

Disconnect power supply before any repairs or maintenance works.

Protect the unit against moisture and do not use wet cloths for cleaning.

Use the device in working order only, disconnect power supply in case of any faults.

Check the electrical system before connecting the heating unit.

The unit must be earthed.

The  unit  is  connected  to  the  electrical  system  with  residual  device  and  protective 

terminal (earth).

The thermostat preventing overheating must be connected in the heating unit control 

system.

Do not switch on the unit without the fan running.

Potential  free  state  is  obtained  by  disconnecting  the  power  supply  cable  from  the 

socket.

Due to its design, the device does not emit any hazardous radiation. 

Important note! Any installation or use of the fan not in accordance with the instruction 

manual may cause the fan damage and voids the warranty.

Despite  the  fact  that  the  device  has  been  designed  and  manufactured  in  accordance  with  the 

standards  valid  as  for  the  moment  of  the  manufacture  start,  probability  of  injury  and  damage 

to health when using the device is unavoidable. This probability is related to frequency of using, 

cleaning and repairing the device, presence of persons within the danger area, and not respecting 

the safety rules as set out in the instruction. 

Summary of Contents for AGE-1-3
















Reviews: