ASSEMBLY INSTRUCTIONS
1. Turn Transfer Bench Long Seat Upside Down
• Place seat on flat surface i.e. table or floor, upside down so underside is
facing you
• Side of seat with handle should be on the right as you look at underside of
seat, (Refer to image 3)
2. Connect First U-Shaped Leg Brace and Back-Rest Support Bar
• Lay U-Shaped Leg Brace #1 across underside of seat, in channel closest to
you. Make sure it is resting in recessed channel such that the legs are flaring
out, (Refer to image 5)
IMPORTANT.
• Lay first Back-Rest Support bar across the U-Shaped Leg Brace and align
the hole with the U-Shaped Leg Brace. Fasten with first Butterfly Bolt with
Washer - Long. Tighten but not all the way. (Refer to image 6, position 1).
• Make sure direction of Back-Rest Support Bars is correct for specific
bathtub orientation, right-facing or left-facing bathtub.
IMPORTANT.
3. Connect Second U-Shaped Leg Brace
• Lay second U-Shaped Leg Brace across bottom of seat. Ensure that it is
resting in the channel and that the legs are flaring out, not in.
IMPORTANT.
• Fasten the Back-Rest Support Bar to the second U-Shaped Leg Brace and
underside of seat, (position 2, per image 6), using second Butterfly Bolt with
Washer – Long.
4. Connect Second Back-Rest Support Bar to U-Shaped Leg Braces
• Align holes in second Back-Rest Support Bar and the two U-Shaped Leg
Braces, (see image 6, positions 3 and 4), and fasten to underside of seat
with two Butterfly Bolts with Washers – Long. Fasten but do not overtighten.
5. Install Padded Support Bar
• Install Padded Support Bar to two U-Shaped Leg Braces by aligning holes
and fastening to underside of seat with two Butterfly Bolts with Washers –
Long. (Refer to image 7).
• Make sure that the direction of the Padded Support Bar aligns with the
direction of the two Back-Rest Support Bars
6. Installing Two Leg Stabilizer Bars
• Place first Leg Stabilizer Bar between two U-Shaped Leg Braces such that
the slight “V” in the tube faces up, with seat upside down. (Refer to image 8).
• Use two Hex Bolts with Washers and Hex/Allen Wrench provided. Fasten
both sides of Leg Stabilizer Bar so that it is snug with U-Shaped Leg Braces.
Do not overtighten.
• Repeat fastening process with second Leg Stabilizer Bar and two additional
Hex Bolts with Washers
7. Installing the Adjustable Legs
• For Legs Inside the Bathtub - Take one Adjustable Leg with Suction Cup
Foot and slide it over the U-Shaped Leg Brace, (see image 9 and 10).
• Press in on Push Pin with thumb on U-Shaped Leg Brace to enable
Adjustable Leg to slide onto U-Shaped Leg Brace. Adjust to desired height,
counting the number of holes.
•
IMPORTANT
– the Push Pin must fully engage with the hole. An audible click
should confirm that the Push Pin is engaged with the hole. The Push Pin
must protrude fully through the hole.
• Repeat process for second Adjustable Leg with Suction Cup Foot.
• For Legs Outside the Bathtub – continue this process with both Adjustable
Legs with Rubber Feet.
5
6
7
8
9
1
2
1
3
2
4
8. Finish Assembly
• Make sure all Butterfly Bolts with Washers and Hex Bolts with Washers are
firmly tightened. Do not overtighten.
• Turn Transfer Bench right side up
• The Padded Back-Rest should face the shower head, shower-bathtub controls.
• The side of the Transfer Bench with the plastic handle and suction cup feet
should be on the INSIDE of the bathtub.
IMPORTANT
• The side of the Transfer Bench with the Padded Support Bar and rubber feet
should be on the OUTSIDE of the bathtub.
IMPORTANT
9. Adjusting the Legs
• Two legs come with suction cup feet.
THESE GO ON THE INSIDE OF THE
BATHTUB
• Two legs come with rubber feet.
THESE GO ON THE OUTSIDE OF THE
BATHTUB
• Use the Push Pins on the Adjustable Legs to ensure that the Transfer Bench
is level. Make sure that the Push Pins are fully engaged with the holes and
fully protruding through the holes.
• Note: the inside floor of some bathtubs is higher than the outside bathroom
floor. Use the product’s adjustable legs to ensure the transfer bench is level.
10. CONNECT PADDED BACK-REST TO BACK-REST SUPPORT BARS
• Insert two back-rest support bars into padded back-rest channels. (refer to
image 11)
• Fasten padded back-rest to back-rest support bars with the two Butterfly
Bolts with Washers – Short. (Refer to image 11)
FEATURES: COMFORT SERIES TRANSFER BENCH
•
Padded Support Bar to assist sitting, standing from Transfer Bench
•
Integrated Handle on inside for support
•
Height adjustable legs from 15” – 23” for proper fit
•
Soft padded seat and backrest for comfort
•
Padded cover pops in and out for easy cleaning
•
Seat and pad have drainage holes to shed water
•
300 lb. weight capacity
•
No-tools easy assembly
•
Fits most standard bathtubs
SAFETY PRECAUTIONS
1. READ ALL INSTRUCTIONS BEFORE USE
2. Make sure all four Adjustable Legs with Rubber Feet or Suction Cups are
securely connected to U-Shaped leg braces. Each push pin must click into
place, be fully visible through the preferred height adjustable hole.
3. Make sure all fastening positions with Butterfly Bolts with Washers are
firmly fastened. Do not overtighten
4. Make sure all four Rubber Feet or Suction Cups are flat on the inside and
outside floors of the bathtub and bathroom.
5. Test Comfort Series Transfer Bench for stability before applying full weight
10
11
