10
Suggestions for the installation and
use of the hood
— The horizontal sections of the pipe must
be slanted slightly upwards (about 10%)
to ensure an easy flow of the air outwards.
— The best performance of the unit is
obtained in the external exhaust model
(suction), therefore in the limits of the
possibilities it is advised to use the
external exhaust (suction) type.
— The best performances are obtained with
short pipes (max. 4 m) and with few
curves.
Electric connection
Before completing any connection, make
sure the house voltage corresponds with
the voltage indicated on the label affixed
inside the hood.
The hood is supplied with a standard plug;
connect it to a correspondingly standard
socket.
In the case is intended to connect the
appliance permanently to the mains after
having removed the plug supplied, must be
fitted a two-pole switch conforming to
regulations with an opening distance
between contacts of not less than 3mm.
The manufacturers are not liable for any
problems caused by the user’s failure to
observe the above instructions.
Fixing the hood
Mounting the hood on the wall
Make use of the scheme N1 provided,
applying it on the wall.
Drill where indicated (fig. 6).
Place the hooks L provided with screws and
blocks in the upper holes.
Place the expansion plugs M supplied with
the hood in the lower holes (fig. 7).
Fix the angle frame N (using either the long
or the short arm, depending on the depth of
the side cupboards) to the wall at the right
height.
Adjust the position of the upper brackets
O, fix the hood to the hooks L, check
that the hood is at the right height (to
eventually adjust the height work on
the screws P, fig. 8).
Fix the hood to the lower angle frame by
means of the screws Q.
For a further adjustment act on the screws
R through the holes S (fig. 8).
Fixing the front panel
Take off the door H (fig. 12) turning the
rear locking knobs K.
Apply the scheme N3 on the rear side of
the front panel, considering that the
arrow indicates the upper side (fig. 13),
drill where indicated by the scheme.
Then fix the door to the front panel by means
of the screws J (fig. 14).
Fixing the hood to the cupboards
Apply the scheme N2 on the side of the
right cupboard, so that the side B
matches the front part of the cupboard
(disregard the thickness of the flap)
and drill two holes 2,5 mm diameter in
the points B1 and B2 (fig. 9).
Then apply the same scheme on the side of
the left cupboard, matching the side C with
the front part of the cupboard (disregard the
thickness of the flap).
Drill two holes 2,5 mm diameter in the
points C1 and C2 (fig. 10).
Fix the hood to the cupboards by means of
the screws T (fig. 11).
Replace the door, inserting it first in the
upper then in the lower slides, turn the rear
locking knobs and then mount the grill,
following in reverse, the operations described
under paragraph “Internal Recycle version”.
Adjust the angle frame tightly to the
wall, making use of the apposite screws
Q (fig. 8).
Summary of Contents for JDS 2230
Page 2: ...2 Fig 1 A B Fig 2 Fig 3 5 4 O 1 2 3 O I 1 18 98 1 10 123 C A 1 2 3 3 D E D E ...
Page 3: ...3 Fig 5 Fig 4 F F G G G N1 L L M M Fig 7 Fig 6 0 90 0 54 54 100 Fig 8 L N O P Q R S ...
Page 4: ...4 Fig 9 Fig 10 B B2 B1 C C2 C1 Fig 11 Fig 12 Fig 14 Fig 13 N2 N2 T T 3 H K N3 J Fig 15 U V ...
Page 12: ...LI08PA ELECTROLUX ZANUSSIHAUSGERÄTEGMBH Rennbahnstraße72 74 D 60528Frankfurt ...
