background image

11

4.2 - Fixing the canopy hood (fig. 3)

1 - Adjust the two screws 

V

 (on the canopy connection points) to approximately half way.

2 - Hook the rear of the canopy to the wall bracket 

1

, after anchoring the latter to the wall.

3 - Turn the screws 

V

 to adjust the canopy vertically and level it horizontally.

4 - Fit and lock the central fixing screw 

V1

 (porvided) to lock the canopy in place.

4.3 - Electrical connection and working test

1 - The safety measures 3.2, 3.3 and 3.4 of paragrapf 3 are to be strictly observed.
2 - Once the electrical connection has been completed, check that worktop illumination, motor

and speed work properly.

4.4 - Ducting or Recirculation fitting

1 - Ducting fitting

a) The cooker hood can be ducted to the outside using either rigid or flexible fire retar-dant

ducting of 120 or 150 mm. The choice is left to the installer. When 120 mm ducting is to
be used it will be necessary to install the reduction flange item 

A

 on the air outlet 

fig. 4

.

b) The installer should provide suitable ducting and sealing material for the installation. The

cooker hood can also be ducted to the outside through one of the rectangular openings
located in either side of the lower section of the chimney stack.

c) If the hood is provided with the charcoal filters fitted, the filters should be removed (see

paragraph 3.3 2 part 2

a

).

2 - Recirculation fitting

a) The filtered air is returned to the room through the two side grilles on the U-shaped lower

section 

I

, which are either formed in the metal itself (bottom position 

fig. 5

).

b) Fit the recirculation spigot item 

R

 into the round outlet on top of the canopy while

pressing down on the spigot until it snaps into position. (Always ensure that into the
recirculation spigot item 

R

 should be fit the two additional spigot item 

P)

.

c) If the hood is provided with the charcoal filters fitted, the filters should be removed (see

paragraph 3.3 2 part 2

a

).

4.5 - Fitting the telescopic chimney stack (fig. 6)

a) To fit the upper section item 

S

 first expand the chimney slightly to allow it to fit over the

wall brackets and then secure the upper section using the 4 screws supplied.

b) The lower section item 

I

 of the chimney stack should be fitted between the lower bracket 

2

and the wall. Fix the U-shaped section to the plastic support, using two of the screws
provided in the bag of accessories.

Part 1

- INSTALLATION INSTRUCTIONS

Summary of Contents for JDK7530E














Reviews: