Juniper SRX340 Hardware Manual Download Page 112

Page: 112 / 150

To list all of the SRX340 Services Gateway components and their serial numbers, enter
the following command:

user@host>

show chassis hardware

Hardware inventory:
Item Version Part number Serial number Description
Chassis CZ3615AN0003 SRX340
Routing Engine REV 02 650-065043 CZ3615AN0003 RE-SRX340
FPC 0 FPC
PIC 0 8xGE,8xGE SFP Base PIC
Power Supply 0

NOTE:

In the

show chassis hardware

command, the Mini-PIM slot number is

reported as an FPC number, and the Mini-PIM number (always 0) is reported
as the PIC number.

Most components also have a serial number ID label attached to the
component body.

Documentation

Contacting Customer Support on page 91

•

Returning a SRX340 Services Gateway Component to Juniper Networks on page 92

•

Locating the SRX340 Services Gateway Chassis Serial Number and Agency Labels on
page 93

•

Locating the SRX340 Services Gateway Mini-Physical Interface Module Serial Number
Label on page 93

•

Information You Might Need to Supply to JTAC on page 94

•

Required Tools and Parts for Packing the SRX340 Services Gateway on page 95

•

Packing the SRX340 Services Gateway for Shipment on page 95

•

Packing SRX340 Services Gateway Components for Shipment on page 96

Information You Might Need to Supply to JTAC

When requesting support from JTAC by telephone, be prepared to provide the following
information:

•

Your existing case number, if you have one

•

Details of the failure or problem

•

Type of activity being performed on the services gateway when the problem occurred

•

Configuration data displayed by one or more

show

commands

•

Your name, organization name, telephone number, fax number, and shipping address

Documentation

Contacting Customer Support on page 91

•

Returning a SRX340 Services Gateway Component to Juniper Networks on page 92

SRX340 Services Gateway Hardware Guide

Summary of Contents for SRX340

























































































































Search results

Summary of Contents for SRX340

Reviews:

Related manuals for SRX340

Brands by name

Popular brands

Juniper SRX340, Hardware Manual

Search results

Summary of Contents for SRX340

Reviews:

Related manuals for SRX340

Brands by name

Popular brands