manualshive.com logo in svg

Juniper QFX5120 Series, Hardware Manual

Share
Download
Juniper QFX5120 Series Hardware Manual Download Page 55

Table 19: AC Power Supply LEDs on QFX5120-48Y Switches

Description

State

Color

LED

The power supply is disconnected from

power, or power is not coming into the

power supply.

Off

Unlit

AC OK

Power is coming into the power supply.

On steadily

Green

The power supply is disconnected from

power, or power is not coming into the

power supply.

Off

Unlit

DC OK

The power supply is sending out power

correctly.

On steadily

Green

An error has been detected in the power

supply. Replace the power supply as soon

as possible. To maintain proper airflow

through the chassis, leave the power

supply installed in the chassis until you are

ready to replace it.

On steadily

Amber

Fault

NOTE:

If the AC OK LED and the DC OK LED are not lit green, either the AC power cord is not

installed properly or the power input voltage is not within normal operating range.

If the AC OK LED is lit green and the DC OK LED is unlit or lit red, the AC power supply is installed

properly, but the power supply has an internal failure.

DC Power Supply in QFX5120 Switches

IN THIS SECTION

Characteristics of a DC Power Supply | 58

DC Power Supply Airflow | 59

57

Summary of Contents for QFX5120 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands