Juniper PTX5000 Hardware Manual Download Page 205 | Manualshive

Page: 205 / 721

background image

Maintaining the PTX5000 AC Power System | 345

Maintaining the PTX5000 DC Power System | 417

Troubleshooting the PTX5000 Power System | 591

Network Cable and Transceiver Planning

IN THIS SECTION

Determining Transceiver Support and Specifications | 187

Fiber-Optic Cable Signal Loss, Attenuation, and Dispersion | 188

Calculating Power Budget and Power Margin for Fiber-Optic Cables | 190

Determining Transceiver Support and Specifications

You can find information about the pluggable transceivers supported on your Juniper Networks device
by using the Hardware Compatibility Tool. In addition to transceiver and connector type, the optical and
cable characteristics—where applicable—are documented for each transceiver. The Hardware
Compatibility Tool allows you to search by product, displaying all the transceivers supported on that
device, or category, displaying all the transceivers by interface speed or type. The Hardware
Compatibility Tool is located at

https://apps.juniper.net/hct/

.

Some transceivers support additional monitoring using the operational mode CLI command

show

interfaces diagnostics optics

. Use the Hardware Compatibility Tool to determine if your transceiver

supports monitoring. See the Junos OS documentation for your device for a description of the
monitoring fields.

CAUTION: The Juniper Networks Technical Assistance Center (JTAC) provides
complete support for Juniper-supplied optical modules and cables. However, JTAC does
not provide support for third-party optical modules and cables that are not qualified or
supplied by Juniper Networks. If you face a problem running a Juniper device that uses
third-party optical modules or cables, JTAC may help you diagnose host-related issues if
the observed issue is not, in the opinion of JTAC, related to the use of the third-party
optical modules or cables. Your JTAC engineer will likely request that you check the

187

«
...
203
204
205
206
207
...
»

Summary of Contents for PTX5000


















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PTX5000

NetDefend DFL-260E

Brand: D-Link Pages: 328

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 19

Brand: D-Link Pages: 22

Brand: Dahua Pages: 12

NetDefend DFL-1600

Brand: D-Link Pages: 23

Brand: TDC Pages: 27

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Maestro E220 Series

Brand: Lantronix Pages: 25

8677 - BladeCenter Rack-mountable - Power...

Brand: IBM Pages: 126

301160U - 1TB Ethernet Disk RAID Network Attached...

Brand: LaCie Pages: 5

BroadLink SP3353

Brand: MicroNet Pages: 66

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

SRA311-008P8 Series

Brand: Divio Pages: 4

Brand: Zhone Pages: 2

Brand: National Instruments Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands