background image

 

Seite 12 

v1.0 

30.05.2022 

[email protected] 

 

Public 

 

Power supply connector 

The device is supplied with 12 V to 48 V DC via a 4-pole 

plug (Phoenix Contact MC 1.5/ 4-STF-3.81),  depending 

on the version. 

1.  PE 

2.  0 V DC 

3.  Ignition (+12 bis 48 V DC) 

4.  +12 bis 48 V DC 

 

 

NOTE 

– PE Schutzleiter und Sicherung 

The protective earth conductor must always be attached. 

Without a protective earth conductor, there is a risk of overvoltage on the device. 

The power supply must be provided with a fuse:  

7 A at 12 V DC; 4 A at 24 V DC; 2 A at 48 V DC. 

 

 

Ignition 

The device starts automatically when the voltage is applied to the Ignition input.  

The  supply  voltage  must  be  constant.  The  permissible  voltage  at  the  IGN  input  corresponds  to  the 

supply voltage of the device. 

Further reactions to state changes at the Ignition input can be defined in the corresponding module of 

the 

Configuration Center

, see section 6.2. 

4.5 

Antennas WLAN and Bluetooth 

The two antennas for 2.4 and 5 GHz WLAN and Bluetooth are protected behind the two plastic covers 

on the back of the device. 

Avoid covering the antennas with metal parts during installation. 

WMT 210 

WMT 215 

 

 

The option "external antenna" deactivates the internal antenna at the rear right (2) and offers it exter-

nally in the service slot via an R-SMA connector. 

Summary of Contents for WMT 210




































Reviews: