background image

 

 

digital audio 
modular 
processing system

 

C8000

 

4/8/16 channels DSP with SDI & system-bus I/O 

C8492(B)

 

   

page

  6/30

 

 

STATUS PANE 

 

 
The status area is quite big for the C8492 so you may face difficulties when displaying it on lower 
resolution displays. You may shrink it by pressing on the little "fly foot print":      

 

Now some information are suppressed and you are able to see the 
most relevant status information without the need to put the browser 
into full screen mode.  

 
 

C8492 DEVICE 00

 

- Given name of the module (may be changed on the 

DEVICE pane). It will be default set during initialization to module type 
amended by the word 

DEVICE

 

and the CAN address 

00

 the module had at 

that moment. 

 

System name of the module and short description. 

 
 

DSP Preset 

Name of the actual loaded preset. 

 

Routing/SDI Preset 

Name of the actual loaded preset. 

 

Failover/Upmix Preset 

Name of the actual loaded preset. 

 

SDI Status  

 

 

[SD / HD / 3G / TG / UNLOCKED] 

Soft LED:  green 

if Rx locked. 

 

yellow  

if Rx  async audio 

 

if Rx un Always ON + Last Valid 

 

red   

if Rx un TG=OFF or TG=AUTO 

 

if TG=Always ON + None 

 

SYNC MASTER

 

appears if the SW1 #5 is set to ON. 

 

BYPASS 

grey / red

 

turns red if a bypass is activated. 

 

DSP1    DSP2 

turns red if the DSP bypass check box is 

SDI       SDI-Relay 

enabled, if the SDI bypass or the  
fail over relay is activated. 

 

Bit Transparent

 

shows the bit transparent status of the 

Ch 01/02 … 07/08 

respective DSP channel pairs. 

Ch 09/10 … 15/16 

 

 

Failover/Upmix

 

turns green if a function is active. 

Upmix 1 

 

Upmix 2 

 

 

Bus/Input Status

 

Error status of the bus inputs (see 
ROUTING). 

 

Processing Status

 

turns green if observation of processing 
status is enabled. Turns red if processing 
status is bad (see DSP1-A Processing 
Status Enable). 

 

Metadata Status

 

turns green if valid metadata are detected. 
Turns red if metadata are corrupted. 

 

SDI De-Embedder Status

 

shows status of the de-embedder 

 

Temperature

 

Module temperature measured on the 
carrier board. 

 

Metering 

clicking on that symbol will open the applet 
to display meter bar graphs (see page 24 
for an example) channels. 

Summary of Contents for C8492































Reviews: